|
|
Sponsored Content
Operating Systems
AIX
Unable to access to p5 9131 AIX system
Post 302784615 by lilyn on Friday 22nd of March 2013 03:12:24 PM
03-22-2013
Hi Michael,
you mean after resetting to default, I suppose to see something on the terminal screen? after reset to factory default, it's the same.
the front panel shows 01 N V=F and below V is T.
Power On/Off System
Current system power state: On
Current firmware boot side: Temporary
Current system server firmware state: Running
System boot speed:Fast
Firmware boot side for the next boot:Temporary
System operating mode:Normal
AIX/Linux partition mode boot:Continue to OS
Boot to system server firmware:Running
System power off policy:Automatic
i5/OS partition mode boot:A
I have the 2 activation code. I can activate VET but don't know where to activate POD code
I did contact the vendor but they no help.
What should I do next?
Thanks.
you mean after resetting to default, I suppose to see something on the terminal screen? after reset to factory default, it's the same.
the front panel shows 01 N V=F and below V is T.
Power On/Off System
Current system power state: On
Current firmware boot side: Temporary
Current system server firmware state: Running
System boot speed:Fast
Firmware boot side for the next boot:Temporary
System operating mode:Normal
AIX/Linux partition mode boot:Continue to OS
Boot to system server firmware:Running
System power off policy:Automatic
i5/OS partition mode boot:A
I have the 2 activation code. I can activate VET but don't know where to activate POD code
I did contact the vendor but they no help.
What should I do next?
Thanks.
Last edited by lilyn; 03-22-2013 at 05:27 PM..
|
|
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi
I need to access files from a specific folder of a Linux system from an another Linux System Remotely.
I know how to, Export a folder on One SCO System & can access the same by using Import via., NFS in the Sco Unix SVR4 System using the scoadmin utility.
Also, I know to use mount -t ... (2 Replies)
Discussion started by: S.Vishwanath
2 Replies
2. Solaris
Good morning,
I have a solaris 8 machine (Sunblade 1000) that is configured with NIS, I have checked everything I can think of to make sure everything is correctly configured which it appears it is but when I try to log into CDE it says it is unable to access my home area and it also does the... (1 Reply)
Discussion started by: Mr Pink
1 Replies
3. Solaris
Hi,
I have two Sun Fire V490 with Solaris 10 5/08, FC switch and two Sun StorageTek 3500 FC arrays. Each array is connected to switch and to one server at a time. In the last week I installed Solaris 10 5/08 on both servers and set up Sun Cluster, version 3.2. At wednesday all was fine - all... (7 Replies)
Discussion started by: Sapfeer
7 Replies
4. Shell Programming and Scripting
I am unable to access the value set inside the loop from outside loop .
Thought of taking this to forum , I had seen other replies also , where a pipe takes the execution to another shell and mentioned thats the reason we do not get the variable outside loop . But I am getting an issue and I am... (1 Reply)
Discussion started by: Armaan_S
1 Replies
5. Solaris
Hi,
I am refered to see Infodoc 80854. but I am not able to access from sun.com. Is there any precedure to view these?. Please guide me.
Thanks in advance. (1 Reply)
Discussion started by: bpsunadm
1 Replies
6. HP-UX
hi friends,
I am using hp unix HP-UX B.11.11 .. Generally i do the compression to maintain the space availability . To compress the files first i used the TAR to collect all the files. it has done fine. when i am using command ls in the folder which has TAR file , it shows the TAR... (2 Replies)
Discussion started by: rdhaprakasam
2 Replies
7. AIX
Hi,
I have tried to setup the console on a Power5 9131-52A type IBM Server. On the back there are 2 RS-232 ports labeled T1 T2. I am going under the assuming that these are the serial ports (Normally the serial ports are S1 S0). When I finish assigning the console under smit, I get no response... (3 Replies)
Discussion started by: mrmurdock
3 Replies
8. AIX
I have recently aquired the following machine:
IBM,9113-550
Up until yesterday we could connect a dumb terminal to serial port 1 and get console login. However the dumb terminal died. We are now using a laptop with a null modem cable attached to serial port 1. This works perfectly for all of... (1 Reply)
Discussion started by: rsw7724
1 Replies
9. Shell Programming and Scripting
Hi,
i have the following code in which i am passing array tldn in awk using -v option & despite of that condition is not getting matched,can somebody suggest how to handle shell arrays in awk
tcount=(9875 9667)
awk -F"\t" -v ltldn="${tldn}" 'NR==FNR {POSTPAIDMDNS=$2"|"$3;next}
... (6 Replies)
Discussion started by: siramitsharma
6 Replies
10. AIX
I am running AIX 7.1 and currently we have samba 3.6.25 installed on the server. As it stands some AIX folders are shared that can be accessed by certain Windows users.
The problem is that since Windows 10 the guest feature no longer works so users have to manually type in their Windows login/pwd... (14 Replies)
Discussion started by: linuxsnake
14 Replies
LEARN ABOUT POSIX
bootctl
BOOTCTL(1) bootctl BOOTCTL(1) NAME
bootctl - Control the firmware and boot manager settings SYNOPSIS
bootctl [OPTIONS...] status bootctl [OPTIONS...] list bootctl [OPTIONS...] update bootctl [OPTIONS...] install bootctl [OPTIONS...] remove DESCRIPTION
bootctl checks, updates, installs or removes the boot loader from the current system. bootctl status checks and prints the currently installed versions of the boot loader binaries and all current EFI boot variables. bootctl list displays all configured boot loader entries. bootctl update updates all installed versions of systemd-boot, if the current version is newer than the version installed in the EFI system partition. This also includes the EFI default/fallback loader at /EFI/BOOT/BOOT*.EFI. A systemd-boot entry in the EFI boot variables is created if there is no current entry. The created entry will be added to the end of the boot order list. bootctl install installs systemd-boot into the EFI system partition. A copy of systemd-boot will be stored as the EFI default/fallback loader at /EFI/BOOT/BOOT*.EFI. A systemd-boot entry in the EFI boot variables is created and added to the top of the boot order list. bootctl remove removes all installed versions of systemd-boot from the EFI system partition, and removes systemd-boot from the EFI boot variables. If no command is passed, status is implied. OPTIONS
The following options are understood: -h, --help Print a short help text and exit. --version Print a short version string and exit. --path= Path to the EFI System Partition (ESP). If not specified, /efi, /boot, and /boot/efi are checked in turn. It is recommended to mount the ESP to /boot, if possible. -p, --print-path This option modifies the behaviour of status. Just print the path to the EFI System Partition (ESP) to standard output and exit. --no-variables Do not touch the EFI boot variables. EXIT STATUS
On success, 0 is returned, a non-zero failure code otherwise. SEE ALSO
Boot loader specification[1] systemd boot loader interface[2] NOTES
1. Boot loader specification https://www.freedesktop.org/wiki/Specifications/BootLoaderSpec 2. systemd boot loader interface https://www.freedesktop.org/wiki/Software/systemd/BootLoaderInterface systemd 237 BOOTCTL(1)