03-22-2013
OK, got past that part but now the 2 new hdisks put into the box are not showing up on SMS. In fact the whole hdisk line is missing. Could I have a firmware issue with the new disks put into such and old machine?
10 More Discussions You Might Find Interesting
1. AIX
Hi guys,
I am trying to install a new machine via nim but it is hanging on 0608 => it should be a network issue
here the situation hoping you will be able to help:
server NIM on a subnet/IP 10.36.12.64
client on 161.43.56.25
the ping test is successful but when I launch the isntall it... (9 Replies)
Discussion started by: touny
9 Replies
2. AIX
Hi Friends,
I've a hard question to ask. I have a NIM server running on AIX 5.3. Now my requirement is that , " From This NIM Server i would like to take the Image of Linux servers ". I mean that using NIM server i should be able to backup / restore the linux Servers.
In Simple terms... (3 Replies)
Discussion started by: rdkumarj
3 Replies
3. AIX
Can a NIM client mksysb restore be performed via NIM (smitty nim) without the NIM client machine having the NIM server's IP and hostname in its /etc/hosts file? (10 Replies)
Discussion started by: kah00na
10 Replies
4. Solaris
when I type start /SP/console... the console shows up but i cannot type anything over there. I do not understand what might be the reason for that.
-> start /SP/console
Are you sure you want to start /SP/console (y/n)? y
Serial console started. To stop, type ESC (
I pressed enter many... (8 Replies)
Discussion started by: bharu_sri
8 Replies
5. AIX
Hello everyone
Im trying to backup a nim client from nim master but I got this message
COMMAND STATUS
Command: failed stdout: yes stderr: no
Before command completion, additional instructions may appear below.
0042-001 nim:... (2 Replies)
Discussion started by: lo-lp-kl
2 Replies
6. AIX
Hi,
I've recently implemented a NIM backup procedure for 2 virtual AIX5.3 environments running on a JS22 blade server. The images transfer to an old p620 box connected to some old SSA storage, each server backs up a mksysb and a savevg image. Now seeing as this method should be replacing our... (3 Replies)
Discussion started by: thinboyslim
3 Replies
7. AIX
Hello guys
I have been trying to restore a VIO server from NIM using the nim_resource.tar file created from the same VIO lpar. The restoration goes fine and after 99% I get the following error
0516-304 putlvodm: Unable to find device id 000b5f62263b70a50000000000000000 in the Device... (1 Reply)
Discussion started by: balaji_prk
1 Replies
8. AIX
Hi All,
I am facing very strange problem. I have created NIM server with 6.1 TL4SP3. I am having SPOT and MKsysb of the same version. I am able to install the client using this spot and mksysb. Now I got the requirement of installing the 5.3 ML11SP3 client. So using the mksysb of 5.3 ML11SP3, I... (3 Replies)
Discussion started by: falgun6666
3 Replies
9. AIX
Hi Guys,
We normally have a backup and restore nightly on our Prod machines. We do this via customized script and all unattended. The dilemma that I'm having is the disabling of the cron after the restore.
I created a nim script to disable the cron after the restore has been completed. But... (6 Replies)
Discussion started by: kaelu26
6 Replies
10. AIX
Hello, I have an AIX6.1 machine which is a nim client to my nim master which is also AIX6.1 machine. I had some problem to perform an installation on my client using smit nim . i removed /etc/niminfo file in order to do the initialization again but when i run the command niminit -a name=client... (0 Replies)
Discussion started by: omonoiatis9
0 Replies
APM(1) APM(1)
NAME
apm - interface with the APM subsystem
SYNOPSIS
apm [ -VvmMsSdin ]
DESCRIPTION
This command requires the Advanced Power Management subsystem. If run without arguments it reads /proc/apm and presents the output in a
human-readable format.
Given a -S or -s option it requests that the machine be put into the APM standby or the APM suspend state, respectively. For a brief
description of these states, see apmd(8).
OPTIONS
-V, --version
Print the version of the program and exit.
-v, --verbose
Also print version information for the APM subsystem. The APM subsystem consists of power-management hardware, firmware usually
referred to as the APM BIOS and a driver in the operating system kernel.
-m, --minutes
Print the time remaining as a number of minutes. The default is to print the time remaining in "hours:minutes" format.
-M, --monitor
Continuously monitor and update the status information. Assumes that the standard output is a terminal.
-S, --standby
Request that the machine be put into the APM standby state.
-s, --suspend
Request that the machine be put into the APM suspend state.
-d, --debug
Print APM status information in a format more useful for debugging. Implies -v.
FILES
/proc/apm
AUTHOR
This program was written by Rik Faith (faith@cs.unc.edu) and may be freely distributed under the terms of the GNU General Public License.
There is ABSOLUTELY NO WARRANTY for this program. The current maintainer is Avery Pennarun (apenwarr@worldvisions.ca).
SEE ALSO
xapm(1), apmd(8).
January 2004 APM(1)