03-12-2013
Possible bottlenecks include your RAID controller, your bus, and your northbridge. Don't think you'd get performance even close to theoretical.
8 More Discussions You Might Find Interesting
1. BSD
Now that SSD drives are becoming mainstream, I had a few questions on installing a SSD drive in a FreeBSD environment. Can FreeBSD be made SSD aware, that is, somehow let FreeBSD know that reads and writes should be limited or deferred to extend the disk's life? Is there a setting for wear... (0 Replies)
Discussion started by: figaro
0 Replies
2. UNIX for Dummies Questions & Answers
Hi
Can someone tell me what are the differences between software and hardware raid ?
thx for help. (2 Replies)
Discussion started by: presul
2 Replies
3. AIX
Hi,
does anyone here happen to know if I could run GLVM or GPFS on Solid State Disks?
I have a high volume / high transaction Sybase HACMP cluster currently setup with SRDF to the DR datacentre. My business now considers to move everything to SSD storage but we still need to get the data to... (0 Replies)
Discussion started by: zxmaus
0 Replies
4. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
5. Solaris
Server Model: T5120 with 146G x4 disks.
OS: Solaris 10 - installed on c1t0d0.
Plan to use software raid (veritas volume mgr) on c1t2d0 disk.
After format and label the disk, still not able to detect using vxdiskadm.
Question:
Should I remove the hardware raid on c1t2d0 first?
My... (4 Replies)
Discussion started by: KhawHL
4 Replies
6. Red Hat
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies
7. UNIX for Dummies Questions & Answers
Hello All,
I recently received a new SSD that I am going to use for the purpose of Booting Virtual Machines. I use VMWare Player to boot Windows Guest Operating Systems onto my Linux Laptop.
I currently have a SSD drive that I use for this exact same purpose that is formatted as ext3 and I'm... (3 Replies)
Discussion started by: mrm5102
3 Replies
8. Linux
I'm running glusterfs on CentOS 6.6 two nodes, (the SSD (samsung 840 1TB x2) is RAID 0 on the HP DL380 G6) x2, and trimming is not enable on it by checking /dev/sdb1/xxxxx/discard_max_bytes=0. Do I still need trimming? Somehow my filesystem is fine with 35-30% free space and running very fast.
... (1 Reply)
Discussion started by: itik
1 Replies
dpt(7D) Devices dpt(7D)
NAME
dpt - DPT ServeRAID IV SCSI host bus adapter and RAID adapter driver
DESCRIPTION
The dpt driver is a driver for the DPT (Distributed Processing Technology) family of SmartRAID IV SCSI HBA and RAID adapters. The following
HBA adapters are supported: PM2024, PM2044UW, PM2044W, PM2124, PM2124W, PM2144UW, and PM2144W.
The following RAID adapters are supported: PM3224, PM3224W, PM3334UW, and PM3334W.
PRECONFIGURATION
o DPT PM3224 only: Only EPROM 7A and later versions are supported.
o DPT PM2024 and PM2124 only: Only EPROM 6D4 and later versions are supported.
o Use adapters with SmartROM version 3.B or later versions only.
o Be sure that the controller board is installed in a PCI bus-mastering slot.
o Disable PCI parity checking if your firmware version is earlier than version 7A, if your system memory is ECC, or if your system does
not check parity.
Known Problems and Limitations
During system boot, a message may be displayed saying a DPT controller driver cannot be installed. This message indicates that the mother-
board installed in your system may contain ECC memory or may not check parity. If you see this message is displayed, disable PCI parity
checking.
Supported Settings
o I/O Address: Auto
CONFIGURATION
Auto-configuration code determines whether the adapter is present at the configured address and what types of devices are attached to it.
The DPT ServeRAID is primarily used as a disk array (system drive) controller.
To configure the attached disk arrays, you must configure the controller (using the configuration utilities provided by the hardware manu-
facturer) before you boot the Solaris operating environment. You use the configuration utilities to set RAID levels, stripe parameters,
cache mechanisms and perform other functions. For more information, see the user manual supplied with your hardware.
FILES
/kernel/drv/dpt.conf dpt configuration file
/dev/dsk/cndn[s|p]n block device
/dev/rdsk/cndn[s|p]n raw device where:
cn controller n
dn LUN n (0-7)
sn UNIX system slice n (0-15)
pn fdisk(1M) partition(0)
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
|Architecture |x86 |
+-----------------------------+-----------------------------+
SEE ALSO
fdisk(1M), attributes(5), cmdk(7D)
SunOS 5.10 27 November 2000 dpt(7D)