Hi
I'm having a big trouble running a configuration tool (ftamtool) which uses xview on sunos 5.8, it refuses to start and says: XView error: could not load font 'FONT_FAMILY_SANS_SERIF...
How to force the program to use installed fonts and where are fonts installed available to use ?
... (0 Replies)
I'm trying to plumb a new interface bge1 on my machine:
root@obms2-com-indianapolis-in:/root# ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet... (3 Replies)
I am looking to get a report on autosys jobs in RUNNING state b/w certain time frame (timeA and timeB).
What I am after is the list of all the jobs that ran between AND during timeA and timeB.
Jobs within the timeframe could either:
A: STARTING --> RUNNING --> SUCCESS/FAILURE etc..
B: ... (0 Replies)
I am looking to get a report on autosys jobs in RUNNING state b/w certain time frame (timeA and timeB).
What I am after is the list of all the jobs that ran between AND during timeA and timeB.
Jobs within the timeframe could either:
A: STARTING --> RUNNING --> SUCCESS/FAILURE etc..
B: ... (0 Replies)
I am looking to get a report on autosys jobs in RUNNING state b/w certain time frame (timeA and timeB).
What I am after is the list of all the jobs that ran between AND during timeA and timeB.
Jobs within the timeframe could either:
A: STARTING --> RUNNING --> SUCCESS/FAILURE etc..
B: ... (2 Replies)
Hi all,
I encounter some problem with my e1000g interface running on sol 10. I can't permanently change the auto-nego to disable, if i use ndd commands, it will only stay until the next reboot.
But i can't change the link speed either is set to /etc/init.d/nddconfig or using ndd commands.
... (1 Reply)
hi frineds
in sunfire 6800 server for one domain when ever i am giving ifconfig -a interface names like hme0,hme1.......are not showing.Actually in the server hme0,hme1,qfe are showing .when i was tried with the cat /etc/path_to_intstshowing tphysical interfcace names .
after giving the... (2 Replies)
on both of my T2000 I am seeing same values of 100Mbps for e1000g0 ethernet port.
i know all four ethernet ports on T2000 are gigabit ports so why is my first link showing as 100Mbps and how can i correct it?
# dladm show-dev
e1000g0 link: up speed: 100 Mbps ... (1 Reply)
Hi All,
Please let me know the step by step process to set the e1000g0 interface speed to 1000mbps with full duplex from 100fdx and how to disable the auto negotiation with switch?.
Thanks and Regards,
Ganesh. (7 Replies)
Discussion started by: gsrungav
7 Replies
LEARN ABOUT OPENSOLARIS
i286
machid(1) User Commands machid(1)NAME
machid, sun, iAPX286, i286, i386, i486, i860, pdp11, sparc, u3b, u3b2, u3b5, u3b15, vax, u370 - get processor type truth value
SYNOPSIS
sun
iAPX286
i386
pdp11
sparc
u3b
u3b2
u3b5
u3b15
vax
u370
DESCRIPTION
The following commands will return a true value (exit code of 0) if you are using an instruction set that the command name indicates.
sun True if you are on a Sun system.
iAPX286 True if you are on a computer using an iAPX286 processor.
i386 True if you are on a computer using an iAPX386 processor.
pdp11 True if you are on a PDP-11/45tm or PDP-11/70tm.
sparc True if you are on a computer using a SPARC-family processor.
u3b True if you are on a 3B20 computer.
u3b2 True if you are on a 3B2 computer.
u3b5 True if you are on a 3B5 computer.
u3b15 True if you are on a 3B15 computer.
vax True if you are on a VAX-11/750tm or VAX-11/780tm.
u370 True if you are on an IBM(R) System/370tm computer.
The commands that do not apply will return a false (non-zero) value. These commands are often used within makefiles (see make(1S)) and
shell scripts (see sh(1)) to increase portability.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO make(1S), sh(1), test(1), true(1), uname(1), attributes(5)NOTES
The machid family of commands is obsolete. Use uname -p and uname -m instead.
SunOS 5.11 5 Jul 1990 machid(1)