03-09-2013
see the other interface o/p:
ossuser@PNR1RAD01 # ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
e1000g0: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 2
inet 10.200.2.73 netmask fffffff8 broadcast 10.200.2.79
e1000g1: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 3
inet 10.200.3.58 netmask ffffffc0 broadcast 10.200.3.63
And one more observation:
root@PNR1RAD01 # dladm show-dev
e1000g0 link: down speed: 0 Mbps duplex: half
e1000g1 link: up speed: 1000 Mbps duplex: full
e1000g2 link: unknown speed: 0 Mbps duplex: half
e1000g3 link: unknown speed: 0 Mbps duplex: half
This link shows down in this command o/p although in ifconfig o/p it shows up but noot the running state as e1000g1 interface.
10 More Discussions You Might Find Interesting
1. Solaris
Hi
I'm having a big trouble running a configuration tool (ftamtool) which uses xview on sunos 5.8, it refuses to start and says: XView error: could not load font 'FONT_FAMILY_SANS_SERIF...
How to force the program to use installed fonts and where are fonts installed available to use ?
... (0 Replies)
Discussion started by: andryk
0 Replies
2. IP Networking
I'm trying to plumb a new interface bge1 on my machine:
root@obms2-com-indianapolis-in:/root# ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet... (3 Replies)
Discussion started by: R37ribution
3 Replies
3. Shell Programming and Scripting
I am looking to get a report on autosys jobs in RUNNING state b/w certain time frame (timeA and timeB).
What I am after is the list of all the jobs that ran between AND during timeA and timeB.
Jobs within the timeframe could either:
A: STARTING --> RUNNING --> SUCCESS/FAILURE etc..
B: ... (0 Replies)
Discussion started by: rgilan01
0 Replies
4. Programming
I am looking to get a report on autosys jobs in RUNNING state b/w certain time frame (timeA and timeB).
What I am after is the list of all the jobs that ran between AND during timeA and timeB.
Jobs within the timeframe could either:
A: STARTING --> RUNNING --> SUCCESS/FAILURE etc..
B: ... (0 Replies)
Discussion started by: rgilan01
0 Replies
5. Solaris
I am looking to get a report on autosys jobs in RUNNING state b/w certain time frame (timeA and timeB).
What I am after is the list of all the jobs that ran between AND during timeA and timeB.
Jobs within the timeframe could either:
A: STARTING --> RUNNING --> SUCCESS/FAILURE etc..
B: ... (2 Replies)
Discussion started by: rgilan01
2 Replies
6. Solaris
Hi all,
I encounter some problem with my e1000g interface running on sol 10. I can't permanently change the auto-nego to disable, if i use ndd commands, it will only stay until the next reboot.
But i can't change the link speed either is set to /etc/init.d/nddconfig or using ndd commands.
... (1 Reply)
Discussion started by: mailbox80
1 Replies
7. Solaris
hi frineds
in sunfire 6800 server for one domain when ever i am giving ifconfig -a interface names like hme0,hme1.......are not showing.Actually in the server hme0,hme1,qfe are showing .when i was tried with the cat /etc/path_to_intstshowing tphysical interfcace names .
after giving the... (2 Replies)
Discussion started by: tv.praveenkumar
2 Replies
8. AIX
Hi Admins,
I am having a whole system lpar in open firmware state on HMC.
How can I bring it to running state ?
Let me know. Thanks. (2 Replies)
Discussion started by: snchaudhari2
2 Replies
9. Solaris
on both of my T2000 I am seeing same values of 100Mbps for e1000g0 ethernet port.
i know all four ethernet ports on T2000 are gigabit ports so why is my first link showing as 100Mbps and how can i correct it?
# dladm show-dev
e1000g0 link: up speed: 100 Mbps ... (1 Reply)
Discussion started by: aliyesami
1 Replies
10. Solaris
Hi All,
Please let me know the step by step process to set the e1000g0 interface speed to 1000mbps with full duplex from 100fdx and how to disable the auto negotiation with switch?.
Thanks and Regards,
Ganesh. (7 Replies)
Discussion started by: gsrungav
7 Replies
ctsmc(7D) Devices ctsmc(7D)
NAME
ctsmc - System Management Controller driver
DESCRIPTION
The ctsmc system management controller driver is a multithreaded, loadable, clonable STREAMS hardware driver that supports communication
with the system management controller device on SUNW,NetraCT-410, SUNW,NetraCT-810 and SUNW,Netra-CP2300 platforms.
The smc device provides a Keyboard Controller Style (KCS) interface as described in the Intelligent Platform Management Interface (IPMI)
Version 1.5 specification. The ctsmc driver enables user-land and kernel-land clients to access services provided by smc hardware.
FILES
/dev/ctsmc
ctsmc special character device
/platform/sun4u/kernel/drv/sparcv9/ctsmc
64 bit ELF kernel driver
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Architecture |SPARC |
+-----------------------------+-----------------------------+
|Availability |SUNWcar.u |
+-----------------------------+-----------------------------+
SEE ALSO
attributes(5)
STREAMS Programmers Guide
Writing Device Drivers
Intelligent Platform Management Interface (IPMI). Version 1.5 - PICMIG, February, 2001
SunOS 5.10 7 Dec 2003 ctsmc(7D)