03-09-2013
nothing was done on the server,
but yes one observation, though it doesn't show running state but the ip defined on this interface is well reachable from another node. This eliminated my suspicion on the cable part. I also restarted the whole server as well but no luck.
Can someone advice further ??
10 More Discussions You Might Find Interesting
1. Solaris
Hi
I'm having a big trouble running a configuration tool (ftamtool) which uses xview on sunos 5.8, it refuses to start and says: XView error: could not load font 'FONT_FAMILY_SANS_SERIF...
How to force the program to use installed fonts and where are fonts installed available to use ?
... (0 Replies)
Discussion started by: andryk
0 Replies
2. IP Networking
I'm trying to plumb a new interface bge1 on my machine:
root@obms2-com-indianapolis-in:/root# ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet... (3 Replies)
Discussion started by: R37ribution
3 Replies
3. Shell Programming and Scripting
I am looking to get a report on autosys jobs in RUNNING state b/w certain time frame (timeA and timeB).
What I am after is the list of all the jobs that ran between AND during timeA and timeB.
Jobs within the timeframe could either:
A: STARTING --> RUNNING --> SUCCESS/FAILURE etc..
B: ... (0 Replies)
Discussion started by: rgilan01
0 Replies
4. Programming
I am looking to get a report on autosys jobs in RUNNING state b/w certain time frame (timeA and timeB).
What I am after is the list of all the jobs that ran between AND during timeA and timeB.
Jobs within the timeframe could either:
A: STARTING --> RUNNING --> SUCCESS/FAILURE etc..
B: ... (0 Replies)
Discussion started by: rgilan01
0 Replies
5. Solaris
I am looking to get a report on autosys jobs in RUNNING state b/w certain time frame (timeA and timeB).
What I am after is the list of all the jobs that ran between AND during timeA and timeB.
Jobs within the timeframe could either:
A: STARTING --> RUNNING --> SUCCESS/FAILURE etc..
B: ... (2 Replies)
Discussion started by: rgilan01
2 Replies
6. Solaris
Hi all,
I encounter some problem with my e1000g interface running on sol 10. I can't permanently change the auto-nego to disable, if i use ndd commands, it will only stay until the next reboot.
But i can't change the link speed either is set to /etc/init.d/nddconfig or using ndd commands.
... (1 Reply)
Discussion started by: mailbox80
1 Replies
7. Solaris
hi frineds
in sunfire 6800 server for one domain when ever i am giving ifconfig -a interface names like hme0,hme1.......are not showing.Actually in the server hme0,hme1,qfe are showing .when i was tried with the cat /etc/path_to_intstshowing tphysical interfcace names .
after giving the... (2 Replies)
Discussion started by: tv.praveenkumar
2 Replies
8. AIX
Hi Admins,
I am having a whole system lpar in open firmware state on HMC.
How can I bring it to running state ?
Let me know. Thanks. (2 Replies)
Discussion started by: snchaudhari2
2 Replies
9. Solaris
on both of my T2000 I am seeing same values of 100Mbps for e1000g0 ethernet port.
i know all four ethernet ports on T2000 are gigabit ports so why is my first link showing as 100Mbps and how can i correct it?
# dladm show-dev
e1000g0 link: up speed: 100 Mbps ... (1 Reply)
Discussion started by: aliyesami
1 Replies
10. Solaris
Hi All,
Please let me know the step by step process to set the e1000g0 interface speed to 1000mbps with full duplex from 100fdx and how to disable the auto negotiation with switch?.
Thanks and Regards,
Ganesh. (7 Replies)
Discussion started by: gsrungav
7 Replies
LEARN ABOUT HPUX
create_clearinghouse
create clearinghouse(1m) create clearinghouse(1m)
NAME
create clearinghouse - Creates a clearinghouse on the local server system or makes an existing clearinghouse available
SYNOPSIS
cdscp create clearinghouse clearinghouse-name
ARGUMENTS
The full name of the clearinghouse.
DESCRIPTION
The create clearinghouse command creates a clearinghouse on the local server system or makes an existing clearinghouse available. The
server start-up command usually creates a new clearinghouse when you configure a new CDS server. Occasionally, you may need to create a
second clearinghouse on a particular server; for example, if you are temporarily relocating a clearinghouse on a different server. See the
OSF DCE Administration Guide for more information about relocating a clearinghouse.
Clearinghouses should be named only in the root. When you enter the command, CDS creates a read-only replica of the root directory and
stores it in the new clearinghouse as the initial replica. Because the process that creates the new clearinghouse initiates a skulk of the
root directory, all replicas of the root should be reachable when you enter the command.
Privilege Required
You need write permission to the server on which you intend to create the clearinghouse and administer permission to the cell root direc-
tory. The server principal needs read, write, and administer permission to the cell root directory.
NOTES
This command is usually executed only by the network configuration procedure. To ensure that all replicas of the root are reachable, per-
form an immediate skulk of /.: prior to issuing this command.
This command is replaced at Revision 1.1 by the dcecp command and may not be provided in future releases of DCE.
EXAMPLE
The following command creates a clearinghouse named /.:/Boston_CH on the local server system: cdscp> create clearinghouse /.:/Boston_CH
RELATED INFORMATION
Commands: clear clearinghouse(1m), delete clearinghouse(1m), list clearinghouse(1m), set cdscp preferred clearinghouse(1m), show cached
clearinghouse(1m), show cdscp preferred clearinghouse(1m), show clearinghouse(1m)
Books: OSF DCE Administration Guide
create clearinghouse(1m)