VOS_CHANGELOC(1)					       AFS Command Reference						  VOS_CHANGELOC(1)

NAME

       vos_changeloc - Change a volume's entry in the VLDB

SYNOPSIS

       vos changeloc [-server] <new server name>
	  [-partition] <new partition location>
	  [-id] <volume name or ID>
	  [-cell <cell name>] [-noauth] [-localauth]
	  [-verbose] [-encrypt] [-noresolve] [-help]

       vos changel [-s] <new server name>
	  [-p] <new partition location>
	  [-i] <volume name or ID>
	  [-c <cell name>]
	  [-noa] [-l] [-v] [-e] [-nor] [-h]

DESCRIPTION

       The vos changeloc command changes the location of a volume in the Volume Location Database (VLDB) without needing to contact the original
       file server on which the volume was hosted. This is useful when a file server has gone down permanently and the data that was stored on
       that server has been moved to a new file server with a different name and IP address (perhaps by mounting the same /vicepX partitions on a
       different host). After moving the data and running vos changeloc, run vos syncvldb and then vos syncserv against the new server to ensure
       full synchronization of the VLDB with the file server.

       In essence, vos changeloc performs the same operations on the VLDB as vos move, but it does NOT move the data from one server's file system
       to another.

CAUTIONS

       Using vos changeloc changes the VLDB without modifying the file server data, so it inherently causes the VLDB to be out of sync with the
       data on the servers. It should only be used when recovering from server failure.  If the servers are on-line, vos move should be used
       instead. It is highly recommended that vos syncvldb and vos syncserv be run after using the vos changeloc command to ensure properly
       synchronization of the VLDB with the file servers.

OPTIONS

       vos changeloc takes the following options:

       -server <new server name>
	   Specifies the new server where the VLDB should believe the volume resides.  Provide the machine's IP address or its host name (either
	   fully qualified or using an unambiguous abbreviation). For details, see vos(1).

       -partition <partition name>
	   Specifies the partition where the VLDB should believe the volume resides.  Provide the -server argument along with this one. Provide
	   the partition's complete name with preceding slash (for example, "/vicepa") or use one of the three acceptable abbreviated forms. For
	   details, see vos(1).

       -id <volume name or ID>
	   Specifies the name or volume ID number on which to operate.

       -cell <cell name>
	   Names the cell in which to run the command. Do not combine this argument with the -localauth flag. For more details, see vos(1).

       -noauth
	   Assigns the unprivileged identity "anonymous" to the issuer. Do not combine this flag with the -localauth flag. For more details, see
	   vos(1).

       -localauth
	   Constructs a server ticket using a key from the local /etc/openafs/server/KeyFile file. The vos command interpreter presents it to the
	   Volume Server and Volume Location Server during mutual authentication. Do not combine this flag with the -cell argument or -noauth
	   flag. For more details, see vos(1).

       -verbose
	   Produces on the standard output stream a detailed trace of the command's execution. If this argument is omitted, only warnings and
	   error messages appear.

       -encrypt
	   Encrypts the command so that the operation's results are not transmitted across the network in clear text. This option is available in
	   OpenAFS versions 1.4.11 or later and 1.5.60 or later.

       -noresolve
	   Shows all servers as IP addresses instead of the DNS name. This is very useful when the server address is registered as 127.0.0.1 or
	   when dealing with multi-homed servers. This option is available in OpenAFS versions 1.4.8 or later and 1.5.35 or later.

       -help
	   Prints the online help for this command. All other valid options are ignored.

OUTPUT

       vos changeloc shows a brief message upon completion:

	  Changed location to server2 /vicepa for volume user.jdoe

EXAMPLES

       The following command changes the location of the "user.jdoe" volume to be /vicepa on the file server machine "server2" while being
       verbose:

	  % vos changeloc server2 a user.jdoe -verbose
	   done
	  Changed location to server2 /vicepa for volume user.jdoe

       The following command changes the location of the "user.jdoe" volume to be /vicepa on "server1" without being verbose:

	  % vos changeloc server1 a user.jdoe
	  Changed location to server1 /vicepa for volume user.jdoe

PRIVILEGE REQUIRED

       The issuer must be listed in the /etc/openafs/server/UserList file on each database server machine. If the -localauth flag is included, the
       issuer must instead be logged on to a server machine as the local superuser "root".

SEE ALSO

       vos(1), vos_move(1), vos_syncserv(1), vos_syncvldb(1)

COPYRIGHT

       Copyright 2007 Jason Edgecombe <jason@rampaginggeek.com>

       This documentation is covered by the BSD License as written in the doc/LICENSE file. This man page was written by Jason Edgecombe for
       OpenAFS.

OpenAFS 							    2012-03-26							  VOS_CHANGELOC(1)