|
|
Sponsored Content
Top Forums
Shell Programming and Scripting
Handling tape errors in script
Post 302777369 by landog on Thursday 7th of March 2013 07:28:28 PM
03-07-2013
|
|
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
hi guys,
I.m trying to remove and add a new tape drive by using the mkdev tape command and when i try to update the Kernel this is what i'm getting,
i386ld: Symbol Sdsk_no_tag in /var/opt/K/SCO/link/1.1.1Eb/etc/conf/pack.d/blad/s
pace.o is multiply defined. First defined in... (0 Replies)
Discussion started by: josramon
0 Replies
2. UNIX for Dummies Questions & Answers
I have a shell script, which calls a load script to load a database. How can i handle errors in Unix(similar to 'error level' in Batch scripts)? I am trying to use 'mailx' to send a Success/failure message based on the error level returned by the load script.
I have already used an error log... (2 Replies)
Discussion started by: sarsani
2 Replies
3. Shell Programming and Scripting
Hi
! /bin/sh
set logdir1 "logDir/local/logname"
#write the filename into a file
echo $logdir1 >> logname.txt
how do i exec the above echo command (1 Reply)
Discussion started by: nathgopi214
1 Replies
4. SCO
when I do a tape status /dev/rStp0 I get the following on a new tape and I have tried several:
Status : ready beginning-of-tape
soft errors : 0
hard errors: 2
underruns: 5
My BackupEdge has stopped backing up my system because it asks for a new volume yet my total system data is under 20... (5 Replies)
Discussion started by: psytropic
5 Replies
5. Shell Programming and Scripting
hi there,
i just need a help handling the output of filespec in case has been picked
im writing a bash script similar to the command ls,
and ive done everything except handing the filespec which i spent more than 3 hrs and i coundn't figure out or find any on the net.
all what i need is... (11 Replies)
Discussion started by: new2Linux
11 Replies
6. UNIX for Dummies Questions & Answers
I'm trying to write a script that will handle the input from the ls command in my script so I can then manipulate the data.
For example, I want to capture the output of the ls command in my script and then do a differences between the filename received in to another directory.
ls |... (1 Reply)
Discussion started by: spookyrtd99
1 Replies
7. Shell Programming and Scripting
Hi All,
How can we handle file operation in scripts. I have written a script that run ok otherwise however the "Cat" operation leaves a process open on the box. Command is like
cat "${LASTFILENAME}" | /usr/xpg4/bin/awk -F, '{do{if ($3 == "100" && $4 == "300" && $170 ~ /^abc/) {
... (2 Replies)
Discussion started by: raman1605
2 Replies
8. Shell Programming and Scripting
Hi,
I need your guys help again. I run a script which check for some process status in a loop. when i check the process some of the process could throw an error, how can i check that inside my script.
Thanks,
RR (3 Replies)
Discussion started by: rrb2009
3 Replies
9. Shell Programming and Scripting
Good Day Everyone,
I was hoping to get a little insight into an expect script that I've written.
Basically we have this expect script to perform an sftp upload, key authentication is not an option, and sftp is the only method supported by our vendor, thus the need for this.
I want to be... (3 Replies)
Discussion started by: thaller
3 Replies
10. Shell Programming and Scripting
Hello
I have a file which has around 120 lines of commands.
I am trying to write a shell script like which reads the 'command' file and executes line by line with some additional (common argument) with maximum 6 commands active at a time. Each of these commands when executed takes time... (5 Replies)
Discussion started by: JackyShane_36
5 Replies
LEARN ABOUT OPENSOLARIS
volcheck
volcheck(1) User Commands volcheck(1) NAME
volcheck - checks for media in a drive and by default checks all floppy media SYNOPSIS
volcheck [-v] [-i secs] [-t secs] pathname DESCRIPTION
The volcheck utility tells volume management to look at each dev/pathname in sequence and determine if new media has been inserted in the drive. The default action is to volcheck all checkable media managed by volume management. OPTIONS
The following options are supported: -i secs Set the frequency of device checking to secs seconds. The default is 2 seconds. The minimum frequency is 1 second. -t secs Check the named device(s) for the next secs seconds. The maximum number of seconds allowed is 28800, which is 8 hours. The fre- quency of checking is specified by -i. There is no default total time. -v Verbose. OPERANDS
The following operands are supported: pathname The path name of a media device. EXAMPLES
Example 1 A sample of the volcheck command. The following example example% volcheck -v /dev/diskette /dev/diskette has media asks volume management to examine the floppy drive for new media. The following example example% volcheck -i 2 -t 600 /dev/diskette1 & asks volume management if there is a floppy in the floppy drive every 2 seconds for 600 seconds (10 minutes). FILES
/dev/volctl volume management control port ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWvolu | +-----------------------------+-----------------------------+ SEE ALSO
eject(1), rmmount(1M), attributes(5) WARNINGS
Due to a hardware limitation in many floppy drives, the act of checking for media causes mechanical action in the floppy drive. Continu- ous polling of the floppy drive will cause the drive to wear out. It is recommended that polling the drive only be performed during periods of high use. SunOS 5.11 28 Feb 2007 volcheck(1)