03-07-2013
yes, you can if the stoarge is an hdisk to the vios, not when the storage is a file or logical volume.
if i recall, just repeat the mkvdev command.
This User Gave Thanks to MichaelFelt For This Post:
10 More Discussions You Might Find Interesting
1. AIX
Hello,
I would like to know if anyone has faced this problem. Whenever there is a duplicate IP address, HACMP goes down infact HACMP ( PowerHA ) takes the whole system down.
Does anyone know how to solve this problem ? (3 Replies)
Discussion started by: filosophizer
3 Replies
2. AIX
hi,
when I do a failover, hacmp always starts db2 but recently it fails to start db2..noticed the issue is db2nodes.cfg is not modified by hacmp and is still showing primary node..manually changed the node name to secondary after which db2 started immediately..unable to figure out why hacmp is... (4 Replies)
Discussion started by: gkr747
4 Replies
3. AIX
I am planning for building a new database server using AIX 6.1 and Oracle 11.2 using ASM.
As i have learned starting with Oracle 11.2 ASM can only be used in conjunction with Clusterware, which is Oracles HA-software. As is the companies policy we do intend to use PowerHA as HA-solution instead... (1 Reply)
Discussion started by: bakunin
1 Replies
4. AIX
Hello!
I have this infraestructure:
- 1 POWER7 with single VIOS on Site A.
- 1 POWER6 with single VIOS on Site B.
- 1 LPAR called NodeA as primary node for PowerHA 6.1 on Site A.
- 1 LPAR called NodeB as secondary (cold) node for PowerHA 6.1 on SiteB.
- 1 Storage DS4700 on Site A.
- 1... (8 Replies)
Discussion started by: enzote
8 Replies
5. AIX
Hello AIX GURU's
Can anybody tell me the steps to crate shared VG (enhanced concurent) for my Lpars from VIO server?
my questions are:
1.
Should I crate Enhanced Concurent VG in VIO and map it using virtual Scsi to Lpar?
or
2. Can I just create virtual SCSI in VIO and map to Lpar and... (1 Reply)
Discussion started by: Vit0_Corleone
1 Replies
6. AIX
Hello,
Lets say for simplicity that I do not use any vlan config inside my server - one lpar group use hea physical port1, another group hea physical port2. Physical port1 configured as vlan1 on external switch, physical port2 as vlan2.
What is the common practice - should I isolate my vios... (0 Replies)
Discussion started by: vilius
0 Replies
7. AIX
Hello,
AIX 6.1 TL7 SP6
POwerHA 6.1 SP10
I was experimenting with new hacmp build. It's 3-node cluster build on AIX 6.1 lpars. It contains Ethernet and diskhb networks. Shared vg disk is SAN disk. Two nodes see disk using vscsi, third node sees disk using npiv. Application is db2 server.
... (4 Replies)
Discussion started by: vilius
4 Replies
8. AIX
hello
ive installed powerha 7.1.3 on two servers aix 6.1.9 6100-09-03-1415
work with dmx4 EMC storgae.
after sync cluster ( terminate with OK ) ive see that the repository disk upper only in one machine :
hdiskpower60 00c7f6b59fc60d9d caavg_private active... (1 Reply)
Discussion started by: ariec
1 Replies
9. AIX
I have created a VxVM disk group in AIX7.1. I have tried to added this VxVM disk group in powerHA 6.1. But in cluster VxVM DGs are not listing. Is there any other procedure to add vxvm diskgroup to hacmp.
Please share me steps for adding vxvm diskgroup to hacmp. (6 Replies)
Discussion started by: sunnybee
6 Replies
10. AIX
Hi All,
As per the IBM upgrade/support matrix
IBM Techdocs Technote: PowerHA for AIX Version Compatibility Matrix
we can't do online upgrade or rolling migration from powerha v7.1.0 to v7.1.3. on AIX61_TL9_SP4, So we are following the steps as below ...
1 ) Bring down the cluster
2 )... (2 Replies)
Discussion started by: linux.amrit
2 Replies
LEARN ABOUT HPUX
lvrmboot
lvrmboot(1M) lvrmboot(1M)
NAME
lvrmboot - remove LVM logical volume link to root, primary swap, or dump volume
SYNOPSIS
autobackup] dump_lv] vg_name
Remarks
cannot be performed if the volume group is activated in shared mode.
DESCRIPTION
This command is supported for arguments belonging to volume groups version 1.0. Attempting this command with arguments belong to volume
groups version 2.0 or higher will result in an error.
The command updates all physical volumes contained in the volume group vg_name such that the logical volume is removed as a root, primary
swap, or dump volume when the system is next booted on the volume group.
Options and Arguments
recognizes the following options and arguments:
vg_name The path name of the volume group.
Set automatic backup for this invocation of this command.
autobackup can have one of the following values:
Automatically back up configuration changes made to the logical volume.
This is the default.
After this command executes, the command (see vgcfgbackup(1M)) is executed for the volume group to which
the logical volume belongs.
Do not back up configuration changes this time.
Remove the definition of
dump_lv as one of the dump volumes. Update the Boot Data Reserved Area.
This option will be obsolete in the next HP-UX release.
Remove the definitions of all of the root, primary swap,
and all dump volumes from the given volume group. Update the Boot Data Reserved Area.
Remove the definition of the primary swap volume
from the given volume group. Update the Boot Data Reserved Area.
This option will be obsolete in the next HP-UX release.
Print verbose messages.
EXTERNAL INFLUENCES
Environment Variables
determines the language in which messages are displayed.
If is not specified or is null, it defaults to "C" (see lang(5)).
If any internationalization variable contains an invalid setting, all internationalization variables default to "C" (see environ(5)).
EXAMPLES
Specify that the logical volume should be removed as one of the dump logical volumes:
Specify that volume group should no longer be a root volume group. Primary swap and dump are also removed.
SEE ALSO
lvlnboot(1M), lvmadm(1M).
lvrmboot(1M)