03-07-2013
I had asked
here
Quote:
is there any way to create shared virtual disk between two LPARs like how you can do it using Storage through Fiber on two servers ?
Trying to stimulate HACMP between two LPARs
and was
replied
Quote:
Originally Posted by
Vit0_Corleone
It's not possible .. you will get error like "resource busy" because it's already reserved for some Lpar
My question:
If I have one VIOS Machine running IVM and SAN Storage connected to it, is there a way to assign one shared disk on two LPARS
- I have one Fiber Card which is on VIOS IVM
- I will assign a disk from Storage to VIOS IVM
- from VIOS IVM how can i assign it to two LPARs for stimulating HACMP ?
thanks
10 More Discussions You Might Find Interesting
1. AIX
Hello,
I would like to know if anyone has faced this problem. Whenever there is a duplicate IP address, HACMP goes down infact HACMP ( PowerHA ) takes the whole system down.
Does anyone know how to solve this problem ? (3 Replies)
Discussion started by: filosophizer
3 Replies
2. AIX
hi,
when I do a failover, hacmp always starts db2 but recently it fails to start db2..noticed the issue is db2nodes.cfg is not modified by hacmp and is still showing primary node..manually changed the node name to secondary after which db2 started immediately..unable to figure out why hacmp is... (4 Replies)
Discussion started by: gkr747
4 Replies
3. AIX
I am planning for building a new database server using AIX 6.1 and Oracle 11.2 using ASM.
As i have learned starting with Oracle 11.2 ASM can only be used in conjunction with Clusterware, which is Oracles HA-software. As is the companies policy we do intend to use PowerHA as HA-solution instead... (1 Reply)
Discussion started by: bakunin
1 Replies
4. AIX
Hello!
I have this infraestructure:
- 1 POWER7 with single VIOS on Site A.
- 1 POWER6 with single VIOS on Site B.
- 1 LPAR called NodeA as primary node for PowerHA 6.1 on Site A.
- 1 LPAR called NodeB as secondary (cold) node for PowerHA 6.1 on SiteB.
- 1 Storage DS4700 on Site A.
- 1... (8 Replies)
Discussion started by: enzote
8 Replies
5. AIX
Hello AIX GURU's
Can anybody tell me the steps to crate shared VG (enhanced concurent) for my Lpars from VIO server?
my questions are:
1.
Should I crate Enhanced Concurent VG in VIO and map it using virtual Scsi to Lpar?
or
2. Can I just create virtual SCSI in VIO and map to Lpar and... (1 Reply)
Discussion started by: Vit0_Corleone
1 Replies
6. AIX
Hello,
Lets say for simplicity that I do not use any vlan config inside my server - one lpar group use hea physical port1, another group hea physical port2. Physical port1 configured as vlan1 on external switch, physical port2 as vlan2.
What is the common practice - should I isolate my vios... (0 Replies)
Discussion started by: vilius
0 Replies
7. AIX
Hello,
AIX 6.1 TL7 SP6
POwerHA 6.1 SP10
I was experimenting with new hacmp build. It's 3-node cluster build on AIX 6.1 lpars. It contains Ethernet and diskhb networks. Shared vg disk is SAN disk. Two nodes see disk using vscsi, third node sees disk using npiv. Application is db2 server.
... (4 Replies)
Discussion started by: vilius
4 Replies
8. AIX
hello
ive installed powerha 7.1.3 on two servers aix 6.1.9 6100-09-03-1415
work with dmx4 EMC storgae.
after sync cluster ( terminate with OK ) ive see that the repository disk upper only in one machine :
hdiskpower60 00c7f6b59fc60d9d caavg_private active... (1 Reply)
Discussion started by: ariec
1 Replies
9. AIX
I have created a VxVM disk group in AIX7.1. I have tried to added this VxVM disk group in powerHA 6.1. But in cluster VxVM DGs are not listing. Is there any other procedure to add vxvm diskgroup to hacmp.
Please share me steps for adding vxvm diskgroup to hacmp. (6 Replies)
Discussion started by: sunnybee
6 Replies
10. AIX
Hi All,
As per the IBM upgrade/support matrix
IBM Techdocs Technote: PowerHA for AIX Version Compatibility Matrix
we can't do online upgrade or rolling migration from powerha v7.1.0 to v7.1.3. on AIX61_TL9_SP4, So we are following the steps as below ...
1 ) Bring down the cluster
2 )... (2 Replies)
Discussion started by: linux.amrit
2 Replies
LEARN ABOUT DEBIAN
simplify
SIMPLIFY(1) General Commands Manual SIMPLIFY(1)
NAME
simplify - a script to simplify a MIME message
SYNOPSIS
simplify [args ...] < message > othermessage
DESCRIPTION
This manual page documents briefly the simplify command. simplify is a Perl script to simplify a MIME message.
This script never loads the entire message into memory, but does dump it's entire contents to disk once.
OPTIONS
mime=no
Don't use MIME, no HTML mail allowed.
testing=yes
Run in testing mode (suppress randonmess)
saveall=yes
Save all attachments to files.
temp=/path/to/working/dir/
Defaults to /tmp.
url=http://box/path/
URL-prefix for printing paths to attachments
header=text...
Text preceding the attachment URL list.
textsig=/path/to/file
Text signature to append to text parts.
htmlsig=/path/to/file
HTML signature to append to HTML parts.
If "saveall" is yes, then the script will save all attachments to disk so people can access their contents later. If an URL is specified
then that automatically implies "saveall=yes". Without this, the default behavior is to only save text and html parts, and delete them and
all working directories when the script is finished.
SEE ALSO
sanitizer(1). More info on configuration: /usr/share/doc/sanitizer/sanitizer.html
AUTHOR
Bjarni R. Einarsson <bre@klaki.net>
This manual page was written by Alberto Gonzalez Iniesta <agi@agi.as> for the Debian GNU/Linux system (but may be used by others).
May 14, 2003 SIMPLIFY(1)