I hope you have code to store the contents of file "amended_file_01" into variable "amended_file01"; after which a minor adjustment to your sed one-liner should do the trick:
This User Gave Thanks to balajesuri For This Post:
using sed to replace a specific string on a specific line number using variables
this is where i am at
grep -v WARNING output | grep -v spawn | grep -v Passphrase | grep -v Authentication | grep -v '/sbin/tfadmin netguard -C'| grep -v 'NETWORK>' >> output.clean
grep -n Destination... (2 Replies)
Hello ,
I need to extract data from specific byte positions of a file.
I have tried the below command
awk ' { printf "%s", substr($0, 642363,642369}' filename
to extract data between byte positions
642363 and 642369 .
However I did not get the expected result.
I am new to awk... (6 Replies)
I am attempting to replace positions 44-46 with YYY if positions 48-50 = XXX.
awk -F "" '{if (substr($0,48,3)=="XXX") $44="YYY"}1' OFS="" $filename > $tempfile
But this is not working, 44-46 is still spaces in my tempfile instead of YYY. Any suggestions would be greatly appreciated. (9 Replies)
From the existing file, I need to replace specific contents possibly with var every time when the user changes the var.
e.g the contents in the file file.txt is 'My name is $n and I am $y years old' and every time user changed the var outside the file, the contents of the file should be created... (4 Replies)
I'm trying to update a text file via sed/awk, after a lot of searching I still can't find a code snippet that I can get to work.
Brief overview:
I have user input a line to a variable, I then find a specific value in this line 10th field in this case. After asking for new input and doing some... (14 Replies)
my requirement is,
consider a file output
cat output
blah sdjfhjkd jsdfhjksdh
sdfs 23423 sdfsdf sdf"sdfsdf"sdfsdf"""""dsf
hellow there
this doesnt look good
et cetc etc
etcetera
i want to replace a line of line number 4 ("this doesnt look good") with some other line
... (3 Replies)
Hello,
I have two files: file1 and file2
file1 has the following info:
---
host: "localhost"
port: 3000
reporter_type: "zookeeper"
zk_hosts:
- "localhost:2181"
file2 contains an IP address (1.1.1.1)
What I want to do is replace localhost with 1.1.1.1, so that the... (4 Replies)
Hi,
I have a file with hundreds of lines. I want to search for particular lines starting with 4000, search and replace the 137-139 position characters; which will be '000', with '036'. Can all of this be done without opening a temp file and then moving that temp file to the original file name.
... (7 Replies)
I have a fixed-length positional file. I am trying to replace content of position 4-13 (length=10) with xxxxxxxxxx.
Sample 2 rows in this file:
H0187459823 172SMITH, JOE
H0112345678 172DOE, JANE
In this example 87459823 (from 1st line) and 12345678 (from 2nd line) (both in position... (3 Replies)
Discussion started by: Diver181
3 Replies
LEARN ABOUT ULTRIX
cut
cut(1) General Commands Manual cut(1)Name
cut - cut out selected fields of each line of a file
Syntax
cut -clist [file1 file2...]
cut -flist [-dchar] [-s] [file1 file2...]
Description
Use the command to cut out columns from a table or fields from each line of a file. The fields as specified by list can be fixed length,
that is, character positions as on a punched card (-c option), or the length can vary from line to line and be marked with a field delim-
iter character like tab (-f option). The command can be used as a filter. If no files are given, the standard input is used.
Use to make horizontal ``cuts'' (by context) through a file, or to put files together in columns. To reorder columns in a table, use and
Options
list Specifies ranges that must be a comma-separated list of integer field numbers in increasing order. With optional - indicates
ranges as in the -o option of nroff/troff for page ranges; for example, 1,4,7; 1-3,8; -5,10 (short for 1-5,10); or 3- (short
for third through last field).
-clist Specifies character positions to be cut out. For example, -c1-72 would pass the first 72 characters of each line.
-flist Specifies the fields to be cut out. For example, -f1,7 copies the first and seventh field only. Lines with no field delim-
iters are passed through intact (useful for table subheadings), unless -s is specified.
-dchar Uses the specified character as the field delimiter. Default is tab. Space or other characters with special meaning to the
shell must be quoted. The -d option is used only in combination with the -f option, according to XPG3 and SVID2/SVID3.
-s Suppresses lines with no delimiter characters. Unless specified, lines with no delimiters are passed through untouched.
Either the -c or -f option must be specified.
Examples
Mapping of user IDs to names:
cut -d: -f1,5 /etc/passwd
To set name to the current login name for the csh shell:
set name=`who am i | cut -f1 -d" "`
To set name to the current login name for the sh, sh5, and ksh shells:
name=`who am i | cut -f1 -d" "`
Diagnostics
"line too long" A line can have no more than 511 characters or fields.
"bad list for c/f option"
Missing -c or -f option or incorrectly specified list. No error occurs if a line has fewer fields than the list calls
for.
"no fields" The list is empty.
See Alsogrep(1), paste(1)cut(1)