Neo,
i am unsure if there is supposed to be a timestamp but i think the other skins had a full timestamp to the second on when someone posted.
right now i can only see the title - date but no HH:MM:SS any possability of getting this back? (7 Replies)
Hi,
I am attempting to configure my ethernet interface on a Sun Blade 1500. I am testing out my network interface my connecting a crossover cable from my blade to a windows box. I would like to assign an ip address of 10.0.0.2 to "bge0" and netmask of "255.0.0.0". I have typed the following:
... (1 Reply)
Hi
I'm completely new in solaris,and don't know many about it.
I was installed solaris 10 on sun blade 1500,and also I need to install oracle on it.
Now I stuck on some thing and i'm sure that you help me.
When i started Oracle installation system told me that I don't have enogh swap space.... (1 Reply)
Hello,
I'm trying to compile PHP 5.3.6 with Apache2 and MySql 5.5.12. I hit a problem that I can't seem to resolve by myself and I could not find a solution on the web.
It looks like Apache and MySql installed ok, I can start/stop them with no problem.
When I try to compile PHP the... (4 Replies)
Good afternoon all,
First, sorry for my English, this is not my first language but I try my best :).
So, here we go.
A friend of mine gave me an old Sun Blade 1500 he wasn't using. He said it was working fine except for the missing hard drive.
I had in my IT personnal box an old IDE... (33 Replies)
Hi,
I'm using Solaris 8 on a Blade 1500.
I know that IDE drives are limited to around 120GB, but I was told that it's possible to use larger drives with the only caveat that the available size will be that 120 (or is it 128?) GB size.
But when I try, format shows only very low sizes, like... (2 Replies)
Discussion started by: BobSol8
2 Replies
LEARN ABOUT LINUX
dpt
DPT(4) BSD Kernel Interfaces Manual DPT(4)NAME
dpt -- DPT RAID Controller SCSI driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device scbus
device dpt
For one or more EISA cards:
device eisa
For one or more ISA cards:
device isa
For one or more PCI cards:
device pci
To allow PCI adapters to use memory mapped I/O if enabled:
options DPT_ALLOW_MEMIO
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
dpt_load="YES"
DESCRIPTION
The dpt driver supports DPT RAID SCSI controllers.
SmartRAID (PM3???) are "Enterprise" class cards, and SmartCache (PM2???) cards are in the "Workstation" class. The Gen 4 Smart Cache IV
products were a re-issue of the Gen 3 utilizing upgraded (and cheaper to produce) silicon. The PM3334 (Smart RAID III) was not revamped as
there was no upgraded silicon (68040 processor) and it was using the best DPT made. Note there has been customer confusion over the faster
enterprise class card supported by this driver being an older generation. The Gen5 cards are supported by the asr(4) driver.
HARDWARE
The dpt driver provides support for the following RAID adapters:
o DPT Smart Cache Plus
o Smart Cache II (PM2?2?, PM2022 [EISA], PM2024/PM2124 [PCI]) (Gen2)
o Smart RAID II (PM3?2?, PM3021, PM3222)
o Smart Cache III (PM2?3?)
o Smart RAID III (PM3?3?, PM3332 [EISA], PM3334UW [PCI]) (Gen3)
o Smart Cache IV (PM2?4?, PM2042 [EISA], PM2044/PM2144 [PCI]) (Gen4)
o Smart RAID IV
SEE ALSO asr(4), cd(4), ch(4), da(4), sa(4), scsi(4)HISTORY
The dpt driver first appeared in FreeBSD 2.2.6.
AUTHORS
The dpt driver was written by Simon Shapiro and ported to the CAM SCSI system by Justin T. Gibbs.
BSD June 18, 2006 BSD