02-02-2013
Its easy, a two step process.
You only need to edit grub.conf to add another boot option only for the vmlinux image you get into SystemBackup02/boot directory. Run 'install-grub /dev/<device holding SystemBackup02>'.
Hope both primary and backup machines have same architecture & device configurations!!!
A word of caution: It's a bit risky with little scope for mistakes; however don't assume that you are doomed on your mistake (until you delete your own data), if the backup system doesn't boot. You'll need to re-boot them again with a backup CD images and mount the drives temporarily and re-do the process correctly, BUT this time differently (mind that mounting may change paths). I've landed into mess and bounced back too but tensions run always high.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have installed Linux 7.2 on a IBM xseries 235 server with 5 scsi hard drives and ServerRaid-5i Ultra320 scsi controller.
I started my installation by configuring the raid controller. I created 2 arrays, raid 1 and raid5. I then proceeded to install Linux and load the drivers.
After the... (2 Replies)
Discussion started by: cstovall
2 Replies
2. Red Hat
my redhat 9 will not boot. We had a power failure and when the power came back, my redhat linux will not boot.
The machine come up to grub prompt.
I tried the following from grub prompt
root (hd0, then press tab key
partition num:0 filesystem type unknown, partition type 0x83... (7 Replies)
Discussion started by: hassan2
7 Replies
3. UNIX for Dummies Questions & Answers
I am new to UNIX and need help in cloning a HPUX 10.2 Ace 5, can anybody please guide me in making a full system backup.
Real Chess (0 Replies)
Discussion started by: real-chess
0 Replies
4. Linux
Please help. I am new to linux. I wrote a script to run the backup on lunix machine but the job gave me an error. I am using Linux 2.6.14.3. Below is the sample of my script can anyone tell me where went wrong? Thanks in advance.
#!/bin/sh
dat=$(date +%d%b%y)... (5 Replies)
Discussion started by: clement
5 Replies
5. UNIX for Dummies Questions & Answers
hi,
Recently, I had receive one system. it's run on the unix tru64 server.
I looking some log files when i know don't work few months age system backup to tape.
Below error:
INFO:Tape backups to tape tape0 starting
for backup list:
slot2:/disk4
Backup Command Variable... (0 Replies)
Discussion started by: Tlg13team
0 Replies
6. Solaris
I have unix server with OS 5.8 ,,,
I tried ufsdump 0ua -f /dev/rmt/0 / to perform full system backup on tape but I failed could any one give a procedure for full system backup on solaris machine using tapes??? (1 Reply)
Discussion started by: mm00123
1 Replies
7. UNIX for Dummies Questions & Answers
I would like to know if I can do a full system back
up on my Unix Sco openserver 5.0.5 Machine. If so, What
is the syntax to do this or where can I find this
information at?
Also, is it possible to make this tape bootable so
that I can easily do a full system restore? Any
information on... (2 Replies)
Discussion started by: nellenodrog
2 Replies
8. HP-UX
Hello,
I'm still new in HP-UX backup and I want to do a FULL BACKUP of HP-UX server to TAPE device. After reading on several forums and posts, i have list down several steps on how to do a full backup on HP-UX with fbackup. I would like the gurus here to comment/advise on the steps below
1)... (4 Replies)
Discussion started by: miskin
4 Replies
9. UNIX for Advanced & Expert Users
Hi,
In order to have a sand box machine that I could use to test some system changes before going to production state, I'd like to duplicate a working system to a virtual one. Ideally, I'd like to manage to do it this way :
- Make a full system backup excluding the user file system (this... (7 Replies)
Discussion started by: pagaille
7 Replies
10. Solaris
Hello i am new on Solaris, and i need to migrate my old AIX 5.3 to Solaris 11.2
Now i have all apps working fine but i have the backup cause i was reading and i have not idea about what method must i choose.
Btw on AIX i had a mksysb backup to restore all system and obviously another backups to... (4 Replies)
Discussion started by: thorin666
4 Replies
LEARN ABOUT DEBIAN
gpodder-backup
GPODDER-BACKUP(1) User Commands GPODDER-BACKUP(1)
NAME
gpodder-backup - Backup and restore utility for gPodder user data
SYNOPSIS
gpodder-backup [--create|--extract] <archive.gpo.tar.gz> [options] gpodder-backup --purge
DESCRIPTION
This utility can be used to create a dump of the current gPodder data (configuration files + downloads), optionally replacing the real con-
tents of the download folder with zero-byte files (for submitting your data to a bug report without having to transfer lots of data).
OPTIONS
--version
show program's version number and exit
-h, --help
show this help message and exit
-c <FILE>, --create=<FILE>
Create a new archive
-x <FILE>, --extract=<FILE>
Extract an existing archive
-f, --fake-downloads
Store downloads as zero-byte files in backup
-n, --no-covers
Do not include cover files in archive
-D <DIR>, --destination=<DIR>
Extract downloads in different folder
-P, --purge
Remove current data (can be combined with --extract)
USAGE FOR BUG REPORTING
This command is useful if you want to report a bug in gPodder:
gpodder-backup --create bug123.gpo.tar.gz --fake-downloads
Backup your current data to file bug123.gpo.tar.gz, but don't store download data (create zero-size dummy files instead). You can
then attach bug123.gpo.tar.gz to the bug report.
If you are instructed to try gPodder from a "clean state", you can use the following command (be sure to backup your data before!):
gpodder-backup --purge
Remove all gPodder data, so you can start from a clean state
EXAMPLES
gpodder-backup --create today.gpo.tar.gz
Backup your current data to file today.gpo.tar.gz
gpodder-backup --extract mybackup.gpo.tar.gz
Restore (without purging) the contents of mybackup.gpo.tar.gz
gpodder-backup --extract default.gpo.tar.gz --purge
Remove current data, then restore the contents of default.gpo.tar.gz
gpodder-backup --purge
Remove all gPodder data, so you can start from a clean state
EXTRACTING FAKED DOWNLOADS
Please note that any existing downloads will be overwritten with zero-byte files when using the --extract option of the gpodder-backup
utility with a backup created with --fake-downloads
AUTHOR
gpodder-backup was written by Thomas Perl (thp@gpodder.org)
gpodder-backup 1.0 December 2010 GPODDER-BACKUP(1)