EDIT:
Forget it (you did already ) - that was somehow a command for the VIO CLI. A simple lslv -l dprod_0000017 would have done it too. Or as Michael wrote
Last edited by zaxxon; 02-04-2013 at 03:47 AM..
Reason: update to let my wrong info not be uncommented
Does anyone have an idea what this means? hdisk10 is part of vg1. (vg1 has 11 hdisks)
I get this msg every morning @ 5:04 CST
This is the orignal message:
A PROBLEM WAS DETECTED ON Fri Aug 17 03:02:09 PDT 2001 801014
The Service Request Number(s)/Probable Cause or... (2 Replies)
Hi,
Can anyone suggest how I can find out which process is keeping one of my hdisk constantly busy (100%) utilisation, when I ran topas .
Thanks for your feedback
Regards (2 Replies)
When I list the PV's using lspv i see both vpath and hdisk names being listed. I got the info that each vpath is configured for 4 hdisks. Problem is I am not able to add either the hard disks in vpath to the existing non-rootvg. ? need to know the basics of vpath .. (4 Replies)
Hi,
in an environment with svc's and ds8xxx wat disk algorithm should be used and what is the difference here:
I can set the algorithm to Load_balance and to Round_robin (see output below).
some info:
hdisk3 ******** MPIO FC 2145
devices.sddpcm.53.rte 2.2.0.0 COMMITTED ... (1 Reply)
How do you create a dummy hdisk with AIX 6.1? In previous versions, I've used this and works, but now I get this error.
hostname:/:# mkdev -l hdisk57 -c disk -t osdisk -s scsi -p fscsi0 -w 0,10 -d
Method error (/etc/methods/define):
0514-022 The specified connection is not valid.
Any... (2 Replies)
Hi all,
I'm getting some errors on AIX regarding Flashcopy and volume group hard disks.
The script that activates flashcopy showed this errors:
Recreating Flashcopy for lun01_A1
Performing syntax check...
Syntax check complete.
Executing script...
Script execution complete.
SMcli... (1 Reply)
Hi. I found an issue with my appvg present in my server.my server is a single node and not part of hacmp.
pmut3# lspv
hdisk0 00c5c9cf92ebb96a rootvg active
hdisk1 00c5c9cfcf30eee9 appvg
hdisk2 00c5c9cfcf30ef98 ... (5 Replies)
Hi,
Planning to implement script to fetch whether the hdisks are in proper sequence. Need output for incorrect sequence
Correct
#lspv
hdisk0
hdisk1
hdisk2
::::::::::::
hdisk5
Incorrect sequence
#lspv
hdisk0
hdisk6
hdisk7
hdisk10
Any idea pls share (2 Replies)
Some storage/disks have been added to an existing AIX 6.1 server. The admin sent me the list of hdisk#'s for the new disks, but I need the corresponding rhdisk# for the same hdisk. (I know from past experience that the rhdisk that maps to an hdisk is not always the same number. For instance,... (5 Replies)
Discussion started by: sbrower
5 Replies
LEARN ABOUT DEBIAN
ppmtosixel
ppmtosixel(1) General Commands Manual ppmtosixel(1)NAME
ppmtosixel - convert a portable pixmap into DEC sixel format
SYNOPSIS
ppmtosixel [-raw] [-margin] [ppmfile]
DESCRIPTION
Reads a portable pixmap as input. Produces sixel commands (SIX) as output. The output is formatted for color printing, e.g. for a DEC
LJ250 color inkjet printer.
If RGB values from the PPM file do not have maxval=100, the RGB values are rescaled. A printer control header and a color assignment table
begin the SIX file. Image data is written in a compressed format by default. A printer control footer ends the image file.
OPTIONS -raw If specified, each pixel will be explicitly described in the image file. If -raw is not specified, output will default to com-
pressed format in which identical adjacent pixels are replaced by "repeat pixel" commands. A raw file is often an order of magni-
tude larger than a compressed file and prints much slower.
-margin
If -margin is not specified, the image will be start at the left margin (of the window, paper, or whatever). If -margin is speci-
fied, a 1.5 inch left margin will offset the image.
PRINTING
Generally, sixel files must reach the printer unfiltered. Use the lpr -x option or cat filename > /dev/tty0?.
BUGS
Upon rescaling, truncation of the least significant bits of RGB values may result in poor color conversion. If the original PPM maxval was
greater than 100, rescaling also reduces the image depth. While the actual RGB values from the ppm file are more or less retained, the
color palette of the LJ250 may not match the colors on your screen. This seems to be a printer limitation.
SEE ALSO ppm(5)AUTHOR
Copyright (C) 1991 by Rick Vinci.
26 April 1991 ppmtosixel(1)
02-02-2013
) - that was somehow a command for the VIO CLI. A simple lslv -l dprod_0000017 would have done it too. Or as Michael wrote 