01-29-2013
Trying to do DHCP on the zone
The problem isn't that I can't get it to network. I can. I am trying to setup the zone under a Guest LDOM to be able to do DHCP. As I understand it this has to be an IP exclusive zone because IP-shared is just that it shares the entire IP stack with the LDOM and thus the same ether address. So a DHCP reservation is impossible. As is Dynamic DNS name resolution.
9 More Discussions You Might Find Interesting
1. Solaris
hi,
what is the difference between ldom and zone. can we install any other os than sun in ldom.
thanks,
snj. (2 Replies)
Discussion started by: snjksh
2 Replies
2. Solaris
Hi Folks,
I am used to writing scripts to get info by running commands at local zones level from their respective global zone by using zlogin <localzone> "command>" while remaining at the global zone level.
Can the same be done with Guest LDoms while remaining at the control LDOM level?
... (4 Replies)
Discussion started by: momin
4 Replies
3. Solaris
Is anyone aware of a method of configuring the boot order of zones and or LDOMS? (2 Replies)
Discussion started by: os2mac
2 Replies
4. Solaris
Hi,
There is LDOM Guest where I need to expand /u02 file systems on it.
It is residing on a Solaris 11 Hypervisor (Primary Domain).
The storage is expanded on vdisk presented to Hypervisor.
I need steps to expand the /u02 on LDOM Guest. (2 Replies)
Discussion started by: vidya_sagar2003
2 Replies
5. Solaris
T4-2 issues meant replacing motherboard.
I thought the ldom config was automatically saved? Got the oracle document here.
At the moment, unable to get ldoms back - here is the output from a few commands:-
ldm list
NAME STATE FLAGS CONS VCPU MEMORY UTIL UPTIME... (4 Replies)
Discussion started by: psychocandy
4 Replies
6. Solaris
Need assitance in troubleshooting steps . Below is the issue
I have LDOM which has 4 zones on it . One zone logging into the server takes 13sec where as other zones are quick .
Troubleshooting steps which I did
- Checked /var/tmp . Not many files
- We have LDAP but thought that wouldnt be... (7 Replies)
Discussion started by: ajayram_arya
7 Replies
7. Solaris
Hi, hoping someone can help, its been a while since I used Solaris.
After creating a NGZ (non global zone), the NGZ can access the GZ (Global Zone) and the GZ can access the NGZ (using ssh, zlogin)
However, the NGZ cannot access any other netwqork devices, it can't even see the default router
... (2 Replies)
Discussion started by: GazinLincoln
2 Replies
8. Solaris
hello to everyone. im new member here.
i have a problem with a guest ldom on solaris 11 sparc in a T8. I need to access to disk vds assigned to guest domain but from control domain.
I want to modify a parameter in inittab of the guest domain because start guest domain give me problems... (2 Replies)
Discussion started by: Liam_
2 Replies
9. UNIX for Beginners Questions & Answers
I'm really stuck here. I've created an LDOM on a SPARC T4-1 with Solaris 11.4 to run a copy of Linux for SPARC. I got the Linux ISO installed and Linux itself installed and booted OK. The only thing is is that there's no networking available in the Linux guest.
This question is basically the... (7 Replies)
Discussion started by: Michele31416
7 Replies
LEARN ABOUT FREEBSD
hv_utils
HYPER-V(4) BSD Kernel Interfaces Manual HYPER-V(4)
NAME
hv_utils -- Hyper-V Utilities Driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in the system kernel configuration file:
device hyperv
DESCRIPTION
The hv_utils driver provides time keeping, shutdown and heartbeat functionality for FreeBSD guest partitions running on Hyper-V. Hyper-V is
a hypervisor-based virtualization technology from Microsoft. The hv_utils driver is one of the core drivers required to be present in guest
partitions running on Hyper-V. This driver provides the following functionalities to guest partitions:
(a) Time Keeping: The clock inside the guest partition will remain accurate by synchronizing to the clock on the virtualization server via
Timesync service, and with the help of the pluggable time source device.
(b) Integrated shutdown: Guest partitions running FreeBSD can be shut down from Hyper-V Manager console by using the "Shut down" command.
(c) Heartbeat: This feature allows the virtualization server to detect whether the guest partition is running and responsive.
SEE ALSO
hv_ata_pci_disengage(4), hv_netvsc(4), hv_storvsc(4), hv_vmbus(4)
HISTORY
Support for hv_utils first appeared in FreeBSD 10.0. The driver was developed through a joint effort between Citrix Incorporated, Microsoft
Corporation, and Network Appliance Incorporated.
AUTHORS
FreeBSD support for hv_utils was first added by Microsoft BSD Integration Services Team <bsdic@microsoft.com>.
BSD
September 10, 2013 BSD