- checki it out, and if possible, give it a try...
BTW in order for grub to boot from some partition, it must be able to find a "boot sector" (or "boot record") already there.
(in your case, you should at least use `dd' to save your boot sector, and restore it along with your 'tar' stuff..
ok ?
HTH
good luck, and success !
alexandre botao
("comets never dodge")
I think u didnt understand me.
Let me clarify.
I do FULL backup of my Debian Lenny 5 server (machine A) using tar.
The restore of tar backup is Ok..its working great on the spare machine (machine B).
Now on the above running system (the spare machine) i want to create a directory
named "SystemBackup02":
Next time I want to
1. untar the contents of my backup in the "SystemBackup02"
directory.
2.change ip in /SystemBackup02/etc/network/interfaces & modify other confs
3.add an entry in grub, telling grub that it can also boot from this directory.
so the aim is to be able to boot from several versions of system backup
I have installed Linux 7.2 on a IBM xseries 235 server with 5 scsi hard drives and ServerRaid-5i Ultra320 scsi controller.
I started my installation by configuring the raid controller. I created 2 arrays, raid 1 and raid5. I then proceeded to install Linux and load the drivers.
After the... (2 Replies)
my redhat 9 will not boot. We had a power failure and when the power came back, my redhat linux will not boot.
The machine come up to grub prompt.
I tried the following from grub prompt
root (hd0, then press tab key
partition num:0 filesystem type unknown, partition type 0x83... (7 Replies)
Please help. I am new to linux. I wrote a script to run the backup on lunix machine but the job gave me an error. I am using Linux 2.6.14.3. Below is the sample of my script can anyone tell me where went wrong? Thanks in advance.
#!/bin/sh
dat=$(date +%d%b%y)... (5 Replies)
hi,
Recently, I had receive one system. it's run on the unix tru64 server.
I looking some log files when i know don't work few months age system backup to tape.
Below error:
INFO:Tape backups to tape tape0 starting
for backup list:
slot2:/disk4
Backup Command Variable... (0 Replies)
I have unix server with OS 5.8 ,,,
I tried ufsdump 0ua -f /dev/rmt/0 / to perform full system backup on tape but I failed could any one give a procedure for full system backup on solaris machine using tapes??? (1 Reply)
I would like to know if I can do a full system back
up on my Unix Sco openserver 5.0.5 Machine. If so, What
is the syntax to do this or where can I find this
information at?
Also, is it possible to make this tape bootable so
that I can easily do a full system restore? Any
information on... (2 Replies)
Hello,
I'm still new in HP-UX backup and I want to do a FULL BACKUP of HP-UX server to TAPE device. After reading on several forums and posts, i have list down several steps on how to do a full backup on HP-UX with fbackup. I would like the gurus here to comment/advise on the steps below
1)... (4 Replies)
Hi,
In order to have a sand box machine that I could use to test some system changes before going to production state, I'd like to duplicate a working system to a virtual one. Ideally, I'd like to manage to do it this way :
- Make a full system backup excluding the user file system (this... (7 Replies)
Hello i am new on Solaris, and i need to migrate my old AIX 5.3 to Solaris 11.2
Now i have all apps working fine but i have the backup cause i was reading and i have not idea about what method must i choose.
Btw on AIX i had a mksysb backup to restore all system and obviously another backups to... (4 Replies)
Discussion started by: thorin666
4 Replies
LEARN ABOUT HPUX
vxconfigbackup
vxconfigbackup(1M)vxconfigbackup(1M)NAME
vxconfigbackup - back up disk group configuration
SYNOPSIS
/etc/vx/bin/vxconfigbackup [-l directory] [[dgname ...] | [dgid ...]]
DESCRIPTION
The vxconfigbackup utility can be used to backup up the configuration information for one or more disk groups. The disk groups may be
specified either by name or by ID. If no disk groups are specified, all disk group configurations are backed up.
OPTIONS -l directory
Specifies a directory other than the default where the backup configuration files are to be written.
Note: The default backup directory is /etc/vx/cbr/bk.
EXAMPLES
Back up the configuration of the mydg disk group to the directory /dgbackup/mydg:
vxconfigbackup -l /dgbackup/mydg mydg
FILES
/etc/vx/cbr/bk/dgname.dgid/dgid.dginfo
Default location of backup file for disk group information.
/etc/vx/cbr/bk/dgname.dgid/dgid.diskinfo
Default location of backup file for disk attributes.
/etc/vx/cbr/bk/dgname.dgid/dgid.binconfig
Default location of backup file for binary configuration copy.
/etc/vx/cbr/bk/dgname.dgid/dgid.cfgrec
Default location of backup file for configuration records in vxprint -m format.
NOTES
The vxconfigbackupd daemon automatically backs up a disk group's new configuration to the default backup directory whenever the configura-
tion is changed. The vxconfigbackup command is provided to back up the configuration manually at any other desired time.
The disk group configuration backup and restore utilities do not save any data in the public region. This includes file system or other
application data that is configured within VxVM objects.
SEE ALSO vxconfigbackupd(1M), vxconfigrestore(1M)VxVM 5.0.31.1 24 Mar 2008 vxconfigbackup(1M)