01-28-2013
I would go for a boot -sv from the ok prompt and have a look at the output...
10 More Discussions You Might Find Interesting
1. Solaris
When I installed the SOLARIS 10 OS first time, the desktop would not start up, this was because of network setup. Reinstalled worked. After a week due to some problem I had to reinstall OS, installation went fine and but when i reboot I get this error.
cannot find mis/krtld
boot error loading... (0 Replies)
Discussion started by: johncy_j
0 Replies
2. AIX
I've got an RS6K B50, and i've installed AIX 5.3, TL5. It installs fine, the only customisations i make to the BOS are to change the locale / keyboard layout to UK, and to choose not to install graphical software.
I have no video card in this box, and i connect via a serial console (null modem... (4 Replies)
Discussion started by: craigp84
4 Replies
3. Solaris
Hi all,
I have a SUN server Sun-Fire-V890 running solaris 9, with a remote system console .
Both the IP adresses of the server and the console are in a private network (address 10.67.xxx).
For some reasons I need to give the access to the server from outside address 194.xxx, but I prefer that... (2 Replies)
Discussion started by: aribault
2 Replies
4. AIX
Hi guys,
Got a tiny bit of a problem on one of our servers here at work. I installed AIX 5.3 on the server and that went fine. Then I upgraded to ML 5300-05-01, but now the system just hangs on boot.
The system starts up and the monitor comes on in few minutes, but a few seconds later when... (6 Replies)
Discussion started by: drchris
6 Replies
5. AIX
To All:
I have this AIX machine (see boot process below). The problem was it hangs at:
The ctrmc Subsystem has been started. Subsystem PID is 11906..
I checked with other forums but their advise were just "strong punches in the air" with no specific explanation.
I really appreciate if... (6 Replies)
Discussion started by: aix_xia
6 Replies
6. Ubuntu
Boot process hangs after reaching the following line:
Adding 5853176k swap on /dev/mapper/mch-swap_1. Priority:-1 extents:1 across:5853176kUsing knoppix 6.2 as LiveCD, and mounting the partitions, I got the following:
# /etc/fstab: static file system information.
#
# Use 'blkid -o value -s... (0 Replies)
Discussion started by: fzaker
0 Replies
7. AIX
Hi all,
We have a old Power4 server with AIX version 5.3 installed. Upon boot up, it hangs right after the AIX welcome screen. On the diagnostic load progress LED indicator, I saw that it stopped at '0c32' then after awhile the LED would be blank. The screen on the monitor will hang at the black... (15 Replies)
Discussion started by: a_sim
15 Replies
8. Solaris
I am trying to install Solaris x86 using the Jumpstart server. I run the add_install_client command with appropriate options, and reboot my x86 Target box. The installation starts fine and unattended. After the installation completes and the target goes for a re-boot, it does not boot from the HDD... (9 Replies)
Discussion started by: hemalsid
9 Replies
9. Solaris
Got a strange problem.
I have 4 Solaris servers all configured the same, Solaris 10 x86 update 10.
When I try to ssh from one Solaris 10 server to another server ssh hangs.
I have an identical server and when I try this everything works fine.
The weird thing is if I am root on the server... (1 Reply)
Discussion started by: ccj4467
1 Replies
10. Solaris
Hi Guys,
I have a SunBlade 1500 which I use to practice at home. Suddenly when I power on the server it just displays the solaris banner and Boot device: disk File and args: Then it stops and says " rebooting with command: boot"
It doesn't boot to the kernel. Is there anyway I can possibly... (5 Replies)
Discussion started by: cjashu
5 Replies
LEARN ABOUT FREEBSD
boot.config
BOOT.CONFIG(5) BSD File Formats Manual BOOT.CONFIG(5)
NAME
boot.config -- Configuration file for the boot blocks
DESCRIPTION
The boot.config file contains options for the FreeBSD boot block code.
When the FreeBSD boot loader runs, it searches the ``a'' slice of the boot partition for a boot.config file (as a result, slices which are
missing an ``a'' partition require user intervention during the boot process). If the boot.config file is found, its contents are used as
the default configuration options for the boot block code and are echoed to the system console.
A valid format of this file is to put BIOS drive number, a controller type, a unit number, a partition, a kernel file name, and any other
valid boot(8) option on a single line, as it is done at the ``boot:'' prompt.
The options related to the boot image selection described below and all the other options available for boot.config are documented in detail
in the boot(8) manual page.
FILES
/boot.config parameters for the boot blocks (optional)
EXAMPLES
The command:
# echo "-P" > /boot.config
will activate the serial console of FreeBSD.
The command:
# echo "1:ad(1,a)/boot/loader" > /boot.config
will instruct the second stage of boot(8) on the first disk to boot with the third boot(8) stage from the second disk.
The command:
# echo "1:ad(1,a)/boot/loader -P" > /boot.config
will do both of the above.
SEE ALSO
boot(8), loader(8)
AUTHORS
This manual page was written by Daniel Gerzo <danger@FreeBSD.org>.
BSD
May 13, 2007 BSD