Help asap squid with 2 nic cards setup Post: 302761965

9 More Discussions You Might Find Interesting

1. Solaris

NIC cards for sunblade 100

I need to add a PCI NIC to a sunblade 100 running solaris 8. Im new to this and was hoping someone could give me some card names and models which will work for this system and has a driver for this sparc system. thanks

2. IP Networking

Setup 2 NIC cards in one UNIX system

Hi; I have a UNIX box (SCO 5.0.2) with two (2) NIC cards. One card (NIC1) talks to a network 57.14.65.x/27. The other card NIC2) talks to users on 57.14.103.x and 57.14.105.x with subnet mask of 255.255.0.0. If I set NIC2 to this subnet mask (255.255.0.0) it seems like the NIC traffic is now...

3. High Performance Computing

veritas and nic cards

Hello I have 2 machines with 3 NIC cards. When I setup veritas, I receive this message: e1000g1 has an IP address configured on it. It could be a public NIC on ken. Are you sure you want to use e1000g1 for the first private heartbeat link? As if e1000g1 should not have an IP address....

4. HP-UX

routing issues with multiple NIC cards

I am running HP_UX 11.23 with 4 NIC cards (this is our TSM server) I have 4 subnets we are backing across. trying to keep traffic on their subnets. I only have one route statment should I add more. route add net 123.99.8.0 netmask 255.255.255.0 123.99.8.254 route add net 123.99.67.0 netmask...

5. Red Hat

External NIC cards not pinging with each other in RHEL 5.1

We have a setup of two nodes which has two NIC cards in each. One is built in and another is D-Link (external NIC card). We are unable to ping to the external NIC cards in both. Eg: Node A has two IPs 192.168.1.10 (eth0) and 192.168.2.10 (eth1) and Node B has two IPs 192.168.1.20 (eth0) and...

6. HP-UX

HP UX 9000 NIC CARDS

Hello, I am trying to move an HP UX from one locaion to another. The new location don't have any Fiber switches. On the back of my server I see 2 RJ 45 for console management the other for networking , the server also has a fiber NIC card. When I disconnec the fiber and want to user regular...

7. IP Networking

Best reference for understanding low level info on nic cards drivers and functionality

Hi, What is the best reference that gives in detail on nic cards configuration , assigning multiple ip addresses to a single interface, netlink library etc and all basic stuff at this level..? Thanks

8. IP Networking

squid proxy: one NIC for inbound & one NIC for outbound?

I am new in squid proxy. My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)? Thank you in advance!

9. Ubuntu

How do you setup 2 nic cards for squid Ubuntu server?

I have a made my squid proxy, I now have add another nic card to an old CPU using Ubuntu server 12.04. I have seen another post similar however I am new and did not understand some of it. Something about redirecting IP address and IP table? I don't know how to do this.:confused:

LEARN ABOUT NETBSD

daic

DAIC(4) 						   BSD Kernel Interfaces Manual 						   DAIC(4)

NAME

     daic -- isdn4bsd driver for EICON.Diehl active ISDN cards

SYNOPSIS

     daic0 at isa? iomem 0xd8000 irq 10

DESCRIPTION

     The daic driver supports the old Diehl active cards: S, SX, SXn, SCOM and QUADRO.

     For a QUADRO card, the driver will detect the board type and use all four ports, each attached as a controller of its own to the isdn4bsd
     system, which can be listed using the daicctl utility.

     The daic driver interfaces the ISDN card to the ISDN4BSD kernel subsystem.  All lower layer ISDN control is handled by the card. This should
     allow you to run any national ISDN protocol delivered by EICON.Diehl for your card, but the driver has only been tested with the DSS1 proto-
     col and some parts of the cards interface are ISDN protocol dependent.

     The daic driver is written to conform to the software interface documented by Diehl in their ISDN-Karten Benutzerhandbuch from 1992.

MICROCODE DOWNLOAD

     Every active card needs its own operating software before it can work. You have to download this to the card before using it with isdn4bsd.
     Use the daicctl utility to do this, i.e. call daicctl -d te_etsi.sx 1 to download the file te_etsi.sx to controller number 1. Use daicctl -l
     to list all available controllers (and ports). You have to select the correct ISDN protocol file for your ISDN interface, see the Diehl docu-
     mentation for details.

     The cards bootstrap process involves another file, which is independent of the card type you use and the protocol you run. It is called
     download.bin in current versions of the Diehl software distribution and has to be copied to the kernel compile directory under
     dev/microcode/daic and converted into a header file used when compiling the kernel by running make in that directory. Your kernel compile
     will fail and remind you of this if you forget to do this. Due to copyright restrictions we cannot distribute the driver with this file inte-
     grated. But if you own a card, you do have the file (or can get it from the Diehl web server).

SEE ALSO

     daicctl(1)

BUGS

     The driver is not yet finished.

BSD
								 January 30, 1998							       BSD