Hello Everyone,
While trying to configure my network interface card on my system which runs mandrake 7, I have faced many problems. I used commands like netconf, drakconf, ifconfig etc to configure my NIC but of no use.
There is no output for dmesg|grep eth. Does that mean that mandrake... (2 Replies)
Hi,
We have a 4 port Sun gigaswift NIC card on our sun fire server.
If the card is a physical one I know how to check the settings/speed. But since this is a virtual card with 4 ports , I am not sure as how we can check the settings.
Details
-----------
root:/> ifconfig -a
lo0:... (3 Replies)
I have a TOSHIBA AS7000 B150 Sun Box
I wanted to run it with 100M/full duplex
I had added this to the /etc/system file to make to setting permenant So it would be set correctly on reboot.
set eri:eri_adv_100fdx_cap=1
set eri:eri_adv_100hdx_cap=0
set eri:eri_adv_autoneg_cap=0
But when I... (4 Replies)
hai this is nagesh
when i was doing practical , i find some dought.
iam using solaris 9. how can i see the ethernet card speed , wheather it is halfduplex or full duplex.any body please help me (4 Replies)
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Hi,
I would like to know how to change the speed of ethernet card in linux? as it is showing auto-neg using mii-tool -v eth0
and my requirement is 100mbps full duplex.
Regards,
Manoj (3 Replies)
how can we change the nic card speed
please explain through commands & steps ????
and i want to change NIC speed 100 --1000Mbps
and what is full & half duplex gives
thanks in advance (6 Replies)
Hi,
Does anyone know how can I determine the maximum capable speed on a network interface card for different OS like HP, Sun, AIX and Linux.
I am aware of the tool "ethtool" which can be used for Linux. Are there any handly commands or /proc files where I can get this info depending on the OS.... (3 Replies)
Hi,
I have few Solaris (9 and 10) servers, whose consoles are running on 10 MBPs. Now, Network team is changing their switch, which doesn't support 10 MBPs and we need to check if console all of those servers will support 100MBPs or more.
Is there any way to check supported (or maximum supported)... (7 Replies)
Discussion started by: solaris_1977
7 Replies
LEARN ABOUT DEBIAN
txp
TXP(4) BSD Kernel Interfaces Manual TXP(4)NAME
txp -- 3Com 3XP Typhoon/Sidewinder (3CR990) Ethernet interface
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device txp
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_txp_load="YES"
DESCRIPTION
The txp interface provides access to the 10Mb/s and 100Mb/s Ethernet networks via the 3Com Typhoon/Sidewinder chipset.
Basic Ethernet functions are provided as well as support for vlan(4) tag removal and insertion assistance, receive ip(4), tcp(4), and udp(4)
checksum offloading, and transmit ip(4) checksum offloading. There is currently no support for transmit tcp(4) or udp(4) checksum offload-
ing, tcp(4) segmentation, nor ipsec(4) acceleration.
Each of the host's network addresses is specified at boot time with an SIOCSIFADDR ioctl(2). The txp interface employs the address resolu-
tion protocol described in arp(4) to dynamically map between Internet and Ethernet addresses on the local network.
When a txp interface is brought up, by default, it will attempt to auto-negotiate the link speed and duplex mode. The speeds, in order of
attempt, are: 100Mb/s Full Duplex, 100Mb/s Half Duplex, 10 Mb/s Full Duplex, and 10 Mb/s Half Duplex.
The txp supports several media types, which are selected via the ifconfig(8) command. The supported media types are:
media autoselect
Attempt to autoselect the media type (default)
media 100baseTX mediaopt full-duplex
Use 100baseTX, full duplex
media 100baseTX [mediaopt half-duplex]
Use 100baseTX, half duplex
media 10baseT mediaopt full-duplex
Use 10baseT, full duplex
media 10baseT [mediaopt half-duplex]
Use 10baseT, half duplex
HARDWARE
The txp driver supports the following cards:
o 3Com 3CR990-TX-95
o 3Com 3CR990-TX-97
o 3Com 3cR990B-TXM
o 3Com 3CR990SVR95
o 3Com 3CR990SVR97
o 3Com 3cR990B-SRV
SEE ALSO altq(4), arp(4), inet(4), intro(4), ip(4), miibus(4), tcp(4), udp(4), vlan(4), ifconfig(8)HISTORY
The txp driver first appeared in OpenBSD 2.9.
BSD March 12, 2009 BSD