01-24-2013
StorageTek 2540 SAN array
Bought a Sun StorageTek 2540 SAN array a few years ago from a company that was going out of business. When we first set it up, we were able to get all the software (Common Array Manager) and firmware directly from Sun.
We just upgraded the drives, but the array is too large for the firmware. Now that Oracle's taken over, the latest firmware is no longer available.
Any suggestions or help?
10 More Discussions You Might Find Interesting
1. Solaris
I have a Sun Sparc T2000 (Solaris 10 05-08) and have installed a PCI-X 4GB Single Port HBA card in it.
I have one StorageTek 2540 array that I would like to connect to the T2000.
For the moment it would be a single path connection, but I've ordered a 2nd HBA, so eventually it would be... (4 Replies)
Discussion started by: soliberus
4 Replies
2. Solaris
We're moving our production 3510FC to development, so we need to replace the production 3510FC. The 6140 is nice, but pricey.
Here's the question: Would two 2540's (RAID 10) be 'faster' than one 3510? (RAID 10) and faster than one 6140 (RAID 10)?
One StoregeTek 6140 (16x72GB 15k rpm fc-al... (12 Replies)
Discussion started by: buddhavelvet
12 Replies
3. Filesystems, Disks and Memory
Hi,
We have 12x1TB SATA disks in our array and I need to create 10TB volume. I defined new storage profile on array and when I tried to add volume, I faced with ~2TB limit for new volumes. I didn't find how to set another limit on my storage profile. Is there is a way to configure one large... (3 Replies)
Discussion started by: Sapfeer
3 Replies
4. Solaris
Hi,
I have a simple question on how to correctly disable the matrix?
Looking for the Common Array Manager and I do not see this option...
Thank for help (3 Replies)
Discussion started by: bieszczaders
3 Replies
5. Solaris
Hi peeps,
Was wondering if anyone can help me, got a couple of storagetek 2540's that I need to configure. Trouble is I think they were brought as second user as all that came with them was cables.
Does anyone know how to configure them (i.e. create raid sets and map to Luns and present... (1 Reply)
Discussion started by: callmebob
1 Replies
6. Hardware
Hello all !
I am a beginner about system and networking , and after some research on internet , i didn't find any relevant information , so i post here , if someone have an experience with this kind of material or if some documentation about how to connect my storage device on my server.
I... (2 Replies)
Discussion started by: acorradi
2 Replies
7. Filesystems, Disks and Memory
Hi,
I have a question about Sun StorageTek Common Array Manager (CAM): What is the concept of 'host'? Is it the hostname of the server that has access to the managed array? If so, can I use its IP instead of its hostname?
I've found a 'host' under CAM called XYZ (See below). In our... (7 Replies)
Discussion started by: aixlover
7 Replies
8. Hardware
Hi all,
My Sun StorageTek 2540 have redundant batteries, but a battery was failed.
# /opt/SUNWstkcam/bin/sscs list -d MyStorage1 fru
Name FRU Alarm State Status Revision Unique Id
-------------------------- ----------- --------... (2 Replies)
Discussion started by: buyantugs
2 Replies
9. Hardware
Hi Guys and Gals,
Wionder if you could help me, got a problem with a controller on a storagetek 2540, dead when fully powered up but if you reboot, it is ok for a couple of seconds (and you can ping it). Then once the array is fully up, it goes faulty and is un-pingable.
Had anyone... (4 Replies)
Discussion started by: callmebob
4 Replies
10. Solaris
Hi Guys,
I have situation here ...
server M4000 server lost connectivity to storagetek 2540
, storagetek 2540 unable to be ping.From DAS URL the storage is undetected.
Any idea why this is happening. Please share.
Thank you.
Raj (1 Reply)
Discussion started by: muralirajah
1 Replies
nvram(8) System Manager's Manual nvram(8)
NAME
nvram - manipulate firmware NVRAM variables
SYNOPSIS
nvram [ -p ] [ -f filename ] [ -d name ] [ -c ] [ name [= value ]] ...
DESCRIPTION
The nvram command allows manipulation of firmware NVRAM variables. It can be used to get or set a variable. It can also be used to print
all of the variables or set a list of variables from a file. Changes to NVRAM variables are only saved by clean restart or shutdown.
In principle, name can be any string. In practice, not all strings will be accepted. New World machines can create new variables as
desired. Some variables require administrator privilege to get or set.
The given value must match the data type required for name. Binary data can be set using the %xx notation, where xx is the hex value of
the byte. The type for new variables is always binary data.
OPTIONS
-d name
Deletes the named firmware variable.
-f filename
Set firmware variables from a text file. The file must be a list of "name value" statements. The first space on each line is taken
to be the separator between "name" and "value". If the last character of a line is , the value extends to the next line.
-x Use XML format for reading and writing variables. This option must be used before the -p or -f options, since arguments are pro-
cessed in order.
-c Delete all of the firmware variables.
-p Print all of the firmware variables.
EXAMPLES
example% nvram boot-args="-s rd=*hd:10"
Set the boot-args variable to "-s rd=*hd:10". This would specify single user mode with the root device in hard drive partition 10.
example% nvram my-variable="String One%00String Two%00%00"
Create a new variable, my-variable, containing a list of two C-strings that is terminated by a NUL.
example% nvram -d my-variable
Deletes the variable named my-variable.
October 28, 2003 nvram(8)