01-14-2013
Hostroute => Bridge and IP-Forwardings
Hello unix community,
Could anyone tell me what is the macosx command for:
1) ip hostroute to bridge:
ip route add 188.40.1.40/32 dev br0
(linux command)
/32 ist for netmask? Because I use /29.
2) and IP-Forwarding:
net.ipv4.ip_forward = 1
(linux command)
I hope anyone could help me!
6 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello.
I expirince some problems with bridging, i'm pretty new to that technology
I've 2 nic's 1 - wireless rt2500 ra0 canyon cn511 card
2 - e100 intel,
ifconfig ra0 up && iwconfig ra0 essid xxx channel x mode managed bring me wireless connection up
then i do following: brctl addbr br0... (1 Reply)
Discussion started by: hachik
1 Replies
2. IP Networking
Hello all, recently we've created a Bridge on a machine that was being used as an snmp, and we haven't assigned an IP for the bridge interface, instead we've used one extra NIC to make all the administrations, but SNMP is simply not working, any one have a clue on how to do this?
Thanks. (0 Replies)
Discussion started by: Zarnick
0 Replies
3. IP Networking
Hello,
I want to connect 2 machines with a bridge between them to control the traffic i.e. delay, loss rate, etc.
I am using the following solution:
2 end machines with ip-adresses 192.168.0.8 and 192.168.0.16.
1 machine with 2 NIC interface cards: 192.168.0.40 and 192.168.0.41
I have... (9 Replies)
Discussion started by: abhishek2301
9 Replies
4. Solaris
hello everyone, I'm a new user and unix-beginner.
I've just installer solaris 11 on my home server, disabled some services, created a fallback BE, enabled speedstep, etc
and now I'm trying to create some zones. I'd like to have an exclusive ip zone and, as far as I know, I sould assignate it... (12 Replies)
Discussion started by: kimj
12 Replies
5. Ubuntu
I have a laptop running Ubuntu Netbook Remix.
What I want to do is use it to connect to my routers wifi, and then plug my desktop into the laptops ethernet port and be hooked to my routers network without any NAT or ICS.
Desktop>>>>>>Laptop/Wired>>Laptop/Wireless>>>>>Router
I want it to look... (6 Replies)
Discussion started by: schwasskin
6 Replies
6. IP Networking
hello networking folks,
i have 3 virtual machines that need to talk to each other
How can i create a bridge to loopback ?
-net tap,vlan=0,ifname=tap1
where tap1 is connected to lo:1 , tap2 is connected to lo:2 etc
thx (0 Replies)
Discussion started by: TwiceDone
0 Replies
LEARN ABOUT DEBIAN
fdformat
FDFORMAT(8) System Administration FDFORMAT(8)
NAME
fdformat - low-level format a floppy disk
SYNOPSIS
fdformat [options] device
DESCRIPTION
fdformat does a low-level format on a floppy disk. device is usually one of the following (for floppy devices the major = 2, and the minor
is shown for informational purposes only):
/dev/fd0d360 (minor = 4)
/dev/fd0h1200 (minor = 8)
/dev/fd0D360 (minor = 12)
/dev/fd0H360 (minor = 12)
/dev/fd0D720 (minor = 16)
/dev/fd0H720 (minor = 16)
/dev/fd0h360 (minor = 20)
/dev/fd0h720 (minor = 24)
/dev/fd0H1440 (minor = 28)
/dev/fd1d360 (minor = 5)
/dev/fd1h1200 (minor = 9)
/dev/fd1D360 (minor = 13)
/dev/fd1H360 (minor = 13)
/dev/fd1D720 (minor = 17)
/dev/fd1H720 (minor = 17)
/dev/fd1h360 (minor = 21)
/dev/fd1h720 (minor = 25)
/dev/fd1H1440 (minor = 29)
The generic floppy devices, /dev/fd0 and /dev/fd1, will fail to work with fdformat when a non-standard format is being used, or if the for-
mat has not been autodetected earlier. In this case, use setfdprm(8) to load the disk parameters.
OPTIONS
-n, --no-verify
Skip the verification that is normally performed after the formatting.
-V, --version
Output version information and exit.
-h, --help
Display help and exit.
SEE ALSO
fd(4), setfdprm(8), mkfs(8), emkfs(8)
AUTHOR
Werner Almesberger (almesber@nessie.cs.id.ethz.ch)
AVAILABILITY
The fdformat command is part of the util-linux package and is available from ftp://ftp.kernel.org/pub/linux/utils/util-linux/.
util-linux July 2011 FDFORMAT(8)