01-02-2013
should not be hard to find... good luck!
10 More Discussions You Might Find Interesting
1. AIX
I am posting this as an FYI. I burned a lot of time on digging for this solution. The problem was performance between newer AIX p series boxes and a sun 4500 with a fiber nic. I tried many misc. solutions but this turned out to fix the issue. My bandwidth benchmark went from around 20MB/sec to... (1 Reply)
Discussion started by: chuckw
1 Replies
2. UNIX for Dummies Questions & Answers
I have installed in the server a quad ethernet adapter, I'm using two interfaces with two different IP networks, both interfaces are connected to a switch, the switch report that is receiving the same MAC address in both ports so must of the times I have connectivity problems.
Any idea to change... (1 Reply)
Discussion started by: mono673
1 Replies
3. SCO
Hi,
I have my server which has LAN with above model build onboard my Dell Server, I got this driver from SCO Unix website but yet to identify the following option:
1. PCI Slot-
2. Bus-
3. Device-
4. Function-
Would anyone please kindly advice what should the... (0 Replies)
Discussion started by: spiderweb
0 Replies
4. Solaris
I have a Dual Boot system - XP with Solaris 10. I built the system from the ground up with different components and the Ethernet Card built into the Motherboard is a Marvell Yukon Gigabit Ethernet 10/100/1000 T-base, RJ-45 Copper.
I am unable to go to the Web as the Ethernet Card is still not... (2 Replies)
Discussion started by: tubbyrana
2 Replies
5. Solaris
hi all,
How to install onboard ethernet card on Sun SPARC M4000 server? (3 Replies)
Discussion started by: Tlg13team
3 Replies
6. Solaris
Hi,
we have SUN Gigabit ethernet cards at the server, both have 2 lines connected but hiw can I found out which cable is on which port before I configure it: the cards has 4 ports , from right to left the cables are connected at the first right then 2 empty then the last at the left side.
... (1 Reply)
Discussion started by: manni2
1 Replies
7. AIX
All
I am trying allocate an IVE to an LPAR (not a VIO) running AIX 7.1. I am getting the error:
HSCL068A
Explanation
Logical port can not be assigned to Logical Partition because this Logical Partition is not the promiscuous LPAR for the physical port.
Has anyone encountered this... (1 Reply)
Discussion started by: johnf
1 Replies
8. Red Hat
Hi,
I have installed Oracle Enterprise Linux 5 in my PC. After the installation the Ethernet Card is not got detected.
But I could able to get the details using the command lspci -a:
01:00.0 Ethernet controller: Attansic Technology Corp. L1 Gigabit Ethernet Adapter (rev b0).
But I could... (4 Replies)
Discussion started by: chidhu.anu
4 Replies
9. Solaris
Hi Community,
i have one issue with 10 fiber ethernet adapter.
here is my details:
root@new-bpel.example.com #dladm show-dev
bge0 link: unknown speed: 0 Mbps duplex: unknown
bge1 link: up speed: 1000 Mbps duplex: full
qlge2 link:... (4 Replies)
Discussion started by: bentech4u
4 Replies
10. Red Hat
Hello community, I have a Proliant HP DL380P with the following network adapters:
NetXtreme BCM5719 Gigabit Ethernet PCIe (Ethernet 1Gb 4-port 331FLR Adapter)
82580 Gigabit Network Connection (NC365T 4-port Ethernet Server Adapter)
I installed Red Hat 7.2 but it recognizes only the... (9 Replies)
Discussion started by: Lord Spectre
9 Replies
plimit(1) User Commands plimit(1)
NAME
plimit - get or set the resource limits of running processes
SYNOPSIS
plimit [-km] pid...
plimit {-cdfnstv} soft,hard... pid...
DESCRIPTION
If one or more of the cdfnstv options is specified, plimit sets the soft (current) limit and/or the hard (maximum) limit of the indicated
resource(s) in the processes identified by the process-ID list, pid. Otherwise plimit reports the resource limits of the processes identi-
fied by the process-ID list, pid.
Only the owner of a process or the super-user is permitted either to get or to set the resource limits of a process. Only the super-user
can increase the hard limit.
OPTIONS
The following options are supported:
-k On output, show file sizes in kilobytes (1024 bytes) rather than in 512-byte blocks.
-m On output, show file and memory sizes in megabytes (1024*1024 bytes).
The remainder of the options are used to change specified resource limits. They each accept an argument of the form:
soft,hard
where soft specifies the soft (current) limit and hard specifies the hard (maximum) limit. If the hard limit is not specified, the comma
may be omitted. If the soft limit is an empty string, only the hard limit is set. Each limit is either the literal string unlimited, or a
number, with an optional scaling factor, as follows:
nk n kilobytes
nm n megabytes (minutes for CPU time)
nh n hours (for CPU time only)
mm:ss minutes and seconds (for CPU time only)
The soft limit cannot exceed the hard limit.
-c soft,hard Set core file size limits (default unit is 512-byte blocks).
-d soft,hard Set data segment (heap) size limits (default unit is kilobytes).
-f soft,hard Set file size limits (default unit is 512-byte blocks).
-n soft,hard Set file descriptor limits (no default unit).
-s soft,hard Set stack segment size limits (default unit is kilobytes).
-t soft,hard Set CPU time limits (default unit is seconds).
-v soft,hard Set virtual memory size limits (default unit is kilobytes).
OPERANDS
The following operands are supported.
pid Process ID list.
EXIT STATUS
plimit returns the exit value zero on success, non-zero on failure (such as no such process, permission denied, or invalid option).
FILES
/proc/pid/* process information and control files
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWesu |
+-----------------------------+-----------------------------+
SEE ALSO
ulimit(1), proc(1), getrlimit(2), setrlimit(2), proc(4), attributes(5),
SunOS 5.10 8 Jun 1998 plimit(1)