01-02-2013
Thank you
Thank you DukeNuke2. I'm going to see whether I can find the patch you pointed out. You are very helpful.
10 More Discussions You Might Find Interesting
1. AIX
I am posting this as an FYI. I burned a lot of time on digging for this solution. The problem was performance between newer AIX p series boxes and a sun 4500 with a fiber nic. I tried many misc. solutions but this turned out to fix the issue. My bandwidth benchmark went from around 20MB/sec to... (1 Reply)
Discussion started by: chuckw
1 Replies
2. UNIX for Dummies Questions & Answers
I have installed in the server a quad ethernet adapter, I'm using two interfaces with two different IP networks, both interfaces are connected to a switch, the switch report that is receiving the same MAC address in both ports so must of the times I have connectivity problems.
Any idea to change... (1 Reply)
Discussion started by: mono673
1 Replies
3. SCO
Hi,
I have my server which has LAN with above model build onboard my Dell Server, I got this driver from SCO Unix website but yet to identify the following option:
1. PCI Slot-
2. Bus-
3. Device-
4. Function-
Would anyone please kindly advice what should the... (0 Replies)
Discussion started by: spiderweb
0 Replies
4. Solaris
I have a Dual Boot system - XP with Solaris 10. I built the system from the ground up with different components and the Ethernet Card built into the Motherboard is a Marvell Yukon Gigabit Ethernet 10/100/1000 T-base, RJ-45 Copper.
I am unable to go to the Web as the Ethernet Card is still not... (2 Replies)
Discussion started by: tubbyrana
2 Replies
5. Solaris
hi all,
How to install onboard ethernet card on Sun SPARC M4000 server? (3 Replies)
Discussion started by: Tlg13team
3 Replies
6. Solaris
Hi,
we have SUN Gigabit ethernet cards at the server, both have 2 lines connected but hiw can I found out which cable is on which port before I configure it: the cards has 4 ports , from right to left the cables are connected at the first right then 2 empty then the last at the left side.
... (1 Reply)
Discussion started by: manni2
1 Replies
7. AIX
All
I am trying allocate an IVE to an LPAR (not a VIO) running AIX 7.1. I am getting the error:
HSCL068A
Explanation
Logical port can not be assigned to Logical Partition because this Logical Partition is not the promiscuous LPAR for the physical port.
Has anyone encountered this... (1 Reply)
Discussion started by: johnf
1 Replies
8. Red Hat
Hi,
I have installed Oracle Enterprise Linux 5 in my PC. After the installation the Ethernet Card is not got detected.
But I could able to get the details using the command lspci -a:
01:00.0 Ethernet controller: Attansic Technology Corp. L1 Gigabit Ethernet Adapter (rev b0).
But I could... (4 Replies)
Discussion started by: chidhu.anu
4 Replies
9. Solaris
Hi Community,
i have one issue with 10 fiber ethernet adapter.
here is my details:
root@new-bpel.example.com #dladm show-dev
bge0 link: unknown speed: 0 Mbps duplex: unknown
bge1 link: up speed: 1000 Mbps duplex: full
qlge2 link:... (4 Replies)
Discussion started by: bentech4u
4 Replies
10. Red Hat
Hello community, I have a Proliant HP DL380P with the following network adapters:
NetXtreme BCM5719 Gigabit Ethernet PCIe (Ethernet 1Gb 4-port 331FLR Adapter)
82580 Gigabit Network Connection (NC365T 4-port Ethernet Server Adapter)
I installed Red Hat 7.2 but it recognizes only the... (9 Replies)
Discussion started by: Lord Spectre
9 Replies
LEARN ABOUT OSX
git-quiltimport
GIT-QUILTIMPORT(1) Git Manual GIT-QUILTIMPORT(1)
NAME
git-quiltimport - Applies a quilt patchset onto the current branch
SYNOPSIS
git quiltimport [--dry-run | -n] [--author <author>] [--patches <dir>]
[--series <file>]
DESCRIPTION
Applies a quilt patchset onto the current Git branch, preserving the patch boundaries, patch order, and patch descriptions present in the
quilt patchset.
For each patch the code attempts to extract the author from the patch description. If that fails it falls back to the author specified with
--author. If the --author flag was not given the patch description is displayed and the user is asked to interactively enter the author of
the patch.
If a subject is not found in the patch description the patch name is preserved as the 1 line subject in the Git description.
OPTIONS
-n, --dry-run
Walk through the patches in the series and warn if we cannot find all of the necessary information to commit a patch. At the time of
this writing only missing author information is warned about.
--author Author Name <Author Email>
The author name and email address to use when no author information can be found in the patch description.
--patches <dir>
The directory to find the quilt patches.
The default for the patch directory is patches or the value of the $QUILT_PATCHES environment variable.
--series <file>
The quilt series file.
The default for the series file is <patches>/series or the value of the $QUILT_SERIES environment variable.
GIT
Part of the git(1) suite
Git 2.17.1 10/05/2018 GIT-QUILTIMPORT(1)