Hi experts,
In my solaris system when i run the command df -h i got the below response.I have some confusion which i want to share with you guys.1)there are two SWAP file system shows are they same or different?2)if i want to count the total disk space should i take both the swap space or only... (2 Replies)
Hi all,
i just started started learning system programming and want to pursue a career in the sys prog area.
below is the program that use a fork() call.
i read in one of the tutorials that parent process and child process uses different address spaces and runs concurrently.
that meas each... (2 Replies)
Hi
I have checked the output of top command in which there is a difference shown between the swap of top command for a process with total swap memory usage of the top command.
Swap usage of process is higher than the total swap memory usage.
top - 18:28:21 up 7:13, 5 users, load... (2 Replies)
Hi,
i have done a blunder here, i increased the swap space on Xen5.6 server machine using below steps :-
1056 dd if=/dev/zero of=/root/myswapfile bs=1M count=1024
1057 ls -l /root/myswapfile
1058 chmod 600 /root/myswapfile
1059 mkswap /root/myswapfile
1060 swapon /root/myswapfile
... (1 Reply)
Hi Everyone,
I have added new Virtual disk to OS. The main point is I need to bring this whole Disk into LVM control, is it necessary to partition the disk using fdisk command and assign partition type as '8e', or can I directly add that disk into LVM, by running pvcreate command with out... (2 Replies)
Hi folks,
How can I scan newly attached network interfaces to server without reboot?
Is there any command or something to scan without reboot.
Thanks (5 Replies)
Hi,
I'm trying to migrate the content of disk 'A' to disk 'B', that they belong to the same vg 'data'_vg'. Whe using pvmove, I get the following error: 'device-mapper: suspend ioctl failed: Interrupted system call'. I put down the whole trace:
pvmove -v "source_disk" "sink_disk"
... (0 Replies)
Hi
I need to identify a newly attached LUN from NetApp on a linuxserver running uname -o
GNU/Linux
I have first run the df -h and got the following:
df -h
Filesystem Size Used Avail Use% Mounted on
/dev/mapper/vg_outsystemdb-lv_root
50G 2.7G 45G ... (3 Replies)
I am working on VM host and collecting data to identify the type of storage attached to the server which will be migrated to VNX.
it has one ldom created on it
luxadm probe output ---
No Network Array enclosures found in /dev/es
Found Fibre Channel device(s):
Node... (7 Replies)
Oflate we are finding a few servers experiencing severe slowness. What would be the commands that I need to try to postmortem the situation? (3 Replies)
Discussion started by: ggayathri
3 Replies
LEARN ABOUT OSF1
volreattach
volreattach(8) System Manager's Manual volreattach(8)NAME
volreattach - Reattaches disk drives that have once again become accessible
SYNOPSIS
/usr/sbin/volreattach [-rb] [accessname...]
/usr/sbin/volreattach -c accessname
OPTIONS
The volreattach utility has the following options: Calls the volrecover utility to attempt to recover stale plexes of any volumes on the
failed disk. Performs the reattach operation in the background. Checks whether a reattach is possible. No operation is performed, but the
name of the disk group and disk media name at which the disk can be reattached is displayed.
DESCRIPTION
The volreattach utility attempts to reattach disks using the same disk group and media names they had before detachment.
This operation may be necessary if a disk has a transient failure, or if some disk drivers are unloaded or unloadable when the Logical
Storage Manager is started, causing disks to enter the failed state.
If the problem is fixed, the volreattach command can be used to reattach the disks without plexes being flagged as stale, as long as the
reattach happens before any volumes on the disk are started.
The volreattach command is called from the voldiskadm menus as part of disk recovery.
The volreattach utility tries to find a disk with a disk group and disk ID matching that of the disk(s) being reattached. If the matching
disk is found, the reattach operation may still fail if the original cause (or some other cause) for the disk failure still exists.
EXIT CODES
A zero exit status is returned if it is possible to perform a reattach. Otherwise, non-zero is returned.
SEE ALSO volintro(8), voldiskadm(8), volrecover(8)volreattach(8)