12-26-2012
interface name is lo0
by the way, the interface name is lo0 not lo
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi, dear all, I am rather new to Unix and have this problem where I cant seem to ping from 1 host to another. The scenerio is as follows: -
1 QNX host->Eth->1 SCO host
the SCO host is configured with it's IP
the QNX host is configured with another IP
both in the same domain, ie, 172.20.3.XX... (3 Replies)
Discussion started by: gavon
3 Replies
2. UNIX for Dummies Questions & Answers
Hello,
hi guys I don't know what is the problem with my NIC I can ping the Localhost (LOOPBACK) but when I run a scripts to check the NIC statuse it's shown the NIC DOWN sooo what could be the problem and what is the best way to start trouplshooting the NIC in SUN-SOLARIS.
Regards,
Karim
... (3 Replies)
Discussion started by: geoquest
3 Replies
3. UNIX for Dummies Questions & Answers
I have Sco openserver 5.0. It had a 125. ip. I changed it to a 192. ip. was unable to ping the 192. I was told to change it in the
etc/tcp
etc/hosts
files which i did. still unable to ping.
i am getting a message unable to route to host.
I also have an error in my etc/tcp file on line... (1 Reply)
Discussion started by: pdoug76
1 Replies
4. UNIX for Dummies Questions & Answers
DEar all
i am receiving this error on start and then unable to ping
(dlpid): unable to open network adapter driver (/dev/mdi/e3h0)
what to do ? (2 Replies)
Discussion started by: sak900354
2 Replies
5. IP Networking
We are unable to bring one of our linux boxes into the network once it was restarted. But once we stop and start the network service. We are able to ping the gateway and get into network. After a minute or two we get the following reponse for the ping command
64 bytes from 124.168.215.40:... (6 Replies)
Discussion started by: chrisanto_2000
6 Replies
6. Solaris
hi,
I setup a Solaris machine in my server room and my client cannot access it. Can anyone advise?
Test that i have done:
-My client pc cannot ping the server.
-My solaris server cannot ping client
-My solaris server can ping it's gateway
-Another NT machine 1 (10.179.30.26) in the server... (2 Replies)
Discussion started by: skiturn
2 Replies
7. IP Networking
hi,
I setup a Solaris machine in my server room and my client cannot access it. Can anyone advise?
Test that i have done:
-My client pc cannot ping the server.
-My solaris server cannot ping client
-My solaris server can ping it's gateway
-Another NT machine 1 (10.179.30.26) in the... (8 Replies)
Discussion started by: skiturn
8 Replies
8. Solaris
Hi ALL,
I Have installed NEW v240 server through hyper terminal, After installation i unable to ping the server from out side server... i can see no entry in resolve.conf file.. but the server has DNS.. willl that issue.. please guide me ping the server from outside within the same network
bk (1 Reply)
Discussion started by: suresh_krish
1 Replies
9. Solaris
Hello,
Am unable to ping the Windows Box, from my Solaris Box.
They both are in same LAN, have the same IP Segments.
Windows IP :: 10.141.14.120
Solaris IP :: 10.141.14.11
Unable to get why isnt working out.... When using the command 'ping 10.141.14.120', it gives the error as 'ping:... (4 Replies)
Discussion started by: jayanto
4 Replies
10. IP Networking
Hello Everyone,
I have unable to run the default server with localhost in my Debian machine. While trying to run Django I get:
Error: That IP address can't be assigned-to.
error
While trying to run galaxy-dist I get this error:
socket.error: Cannot assign requested address
I can't telnet... (3 Replies)
Discussion started by: sachit adhikari
3 Replies
EF(4) BSD Kernel Interfaces Manual EF(4)
NAME
ef -- pseudo-device driver providing support for multiple Ethernet frame types
SYNOPSIS
device ef
DESCRIPTION
The ef pseudo-device driver clones each Ethernet type device with four additional interfaces. Each of them is capable to send or receive
only one predefined frame type.
Names for the new interfaces are created by adding a fN suffix to an existing device name. Where N is a device unit which can have one of
the following values:
0 interface with an Ethernet_II frame
1 interface with a Novell Ethernet_802.3 frame
2 interface with an Ethernet_802.2 frame
3 interface with an Ethernet_802.2/SNAP frame support.
For example, device ed0 will be populated with four devices: ed0f0, ed0f1, ed0f2 and ed0f3.
After that, each device can be configured as usual:
# ifconfig ed0f1 ipx 0x105
This will configure IPX protocol with network number 0x105 and Ethernet_802.3 frame type.
Please note that it is impossible to configure the IPX protocol on the parent ed0 device after the if_ef.ko driver has been loaded.
If the parent interface is not configured for any other protocol (IP for example), subinterfaces will not function. To avoid that, the par-
ent interface should be manually marked as ``up'':
# ifconfig ed0 up
EXAMPLES
The ef driver can be loaded via the loader.conf(5) file:
if_ef_load="YES"
In this case, ordinary interface configuration commands can be used in the rc.conf(5) file:
network_interfaces="ed2 lo0 tun0 ed2f0 ed2f1"
ifconfig_ed2f0_ipx="ipx 0x101"
ifconfig_ed2f1_ipx="ipx 0x102"
DIAGNOSTICS
None.
CAVEATS
Avoid to configure the parent Ethernet device for the IPX protocol, after the ef driver is loaded.
SEE ALSO
ipx(3), ifconfig(8)
AUTHORS
Boris Popov <bp@FreeBSD.org>.
BSD
June 20, 1999 BSD