Hi there
I need to grep for a detail from a file. The pattern to search for involves escape sequences in it. This causes for the problem.
grep "P\_SOME\_STRING\_SEARCH" filename
Note, I have line like below in the file and expect it to grep.
select *
from my_system_param
... (3 Replies)
When I open a file in vi, I see the following characters:
\302\240
Can someone explain what these characters mean. Is it ASCII format? I need to trim those characters from a file.
I am doing the following:
tr -d '\302\240'
---------- Post updated at 08:35 PM ---------- Previous... (1 Reply)
I need to pass congruent or comma character as parameter. i have tried congruent and it prints home directory. is escape char required. And also in awk i have to pass the no to print a column. e.g awk '{print $Param}' (7 Replies)
Hi all,
I was wondering how can i see the special characters like \t, \n or anything else in a file by using Nano or any other linux command like less, more etc (6 Replies)
i need to replace the any special characters with escape characters like below.
test!=123-> test\!\=123
!@#$%^&*()-= to be replaced by
\!\@\#\$\%\^\&\*\(\)\-\= (8 Replies)
grep -i "$line,$opline" COMBO_JUNK|awk -F, '
{
C4+=$4
}
{
}
END {
print C4
}
' OFS=,`
when i run this command in the script.... it o/p all the value as 0 if $line contains any special parameters.....
but the same script if i run in command prompt... it shows... (4 Replies)
Hi
I have a scenario where hyphen(-) from file should be ignored
I used the following code
if && ; then
if ; then
pow=$LINE
echo $pow > history.txt
flag=1
fi
fi
I get the following output
./valid.sh: -: 0403-012 A test... (7 Replies)
Hello gurus,
I have a lookup table
cat tmp1
\\\erw``~ 1
^774574574565665f\] 2
()42543^
and I`m trying to compare a bunch of strings such that, either the lookup table column 1, or the string to be looked up are substrings of each other (and return the second lookup column if yes).
... (2 Replies)
Discussion started by: sheetalk
2 Replies
LEARN ABOUT OPENDARWIN
catch
catch(n) Tcl Built-In Commands catch(n)
__________________________________________________________________________________________________________________________________________________NAME
catch - Evaluate script and trap exceptional returns
SYNOPSIS
catch script ?varName?
_________________________________________________________________DESCRIPTION
The catch command may be used to prevent errors from aborting command interpretation. Catch calls the Tcl interpreter recursively to exe-
cute script, and always returns without raising an error, regardless of any errors that might occur while executing script.
If script raises an error, catch will return a non-zero integer value corresponding to one of the exceptional return codes (see tcl.h for
the definitions of code values). If the varName argument is given, then the variable it names is set to the error message from interpret-
ing script.
If script does not raise an error, catch will return 0 (TCL_OK) and set the variable to the value returned from script.
Note that catch catches all exceptions, including those generated by break and continue as well as errors. The only errors that are not
caught are syntax errors found when the script is compiled. This is because the catch command only catches errors during runtime. When
the catch statement is compiled, the script is compiled as well and any syntax errors will generate a Tcl error.
EXAMPLES
The catch command may be used in an if to branch based on the success of a script.
if { [catch {open $someFile w} fid] } {
puts stderr "Could not open $someFile for writing
$fid"
exit 1
}
The catch command will not catch compiled syntax errors. The first time proc foo is called, the body will be compiled and a Tcl error will
be generated.
proc foo {} {
catch {expr {1 +- }}
}
SEE ALSO
error(n), break(n), continue(n)
KEYWORDS
catch, error
Tcl 8.0 catch(n)