thanks bibinajith, that was helpful. It solved the problem however the other problem remains which is I cannot open the Console from the IVM page. when I click on it, nothing happens. No java applet opens up. Do you know what could be the issue ?
That command will break you out of the restricted shell, and give you root access on the box.
ps -ef | grep http
Shows this /usr/bin/ksh /usr/ios/lpm/sbin/httpdmgr start
so issuing a "restart" there might do the trick.' Executing "/usr/ios/lpm/sbin/httpdmgr start" gave me an error stating that lwistart.sh was not running. I located that at /usr/ios/lpm/gui/httpd/bin/ and executed it.
Issues resolved. everything is working
Last edited by filosophizer; 12-17-2012 at 08:29 AM..
Reason: SOLVED
When using PowerVM Express and IVM (no HMC) on a Power6 P520 , can I configure 2 LPARs in addition to a VIO server, or does the VIO Server count as one of the two LPAR's that PowerVM Express allows? (1 Reply)
Hi everyone,
Sorry if this post is in the wrong place. I searched the forums for "IVM" and it turned up no results. Hopefully someone knows about this. My dilemma is that I have multiple IBM JS12 Express blades in our blade center, each running VIOS 2.1.0.10-FP-20.1 and hosting a couple LPARs. Out... (2 Replies)
Hello,
Lets say for simplicity that I do not use any vlan config inside my server - one lpar group use hea physical port1, another group hea physical port2. Physical port1 configured as vlan1 on external switch, physical port2 as vlan2.
What is the common practice - should I isolate my vios... (0 Replies)
Hello,
I installed PowerVM IVM Virtual I/O on P-550 but later found out that the machine isn't activated for CoD VET code for virtualization.
So when booted , it goes into OPEN Firmware
I/O Hosting requires a hosting partition boot not permitted exit called
> ok
Panel shows > IO... (3 Replies)
I am facing problems in moving CD-ROM from one lpar to another.
CDROM can be seen on the POWERVM (IVM) server , but through the web-access if I move it ( assign it ) to LPAR it will be assigned. I run cfgmgr , and the cdrom does not show up in the LPAR. I firmly believe this is the reason why I... (2 Replies)
Hi All,
I have a p520 box running 3 LPARs, 1 x VIOS, 1 x AIX 6.1 and 1 x AIX 7.1 and no HMC, all configuration is performed via VIOS/IVM
Until recently the box did not have the AIX7.1 LPAR and everything was fine with the box.
We needed to use AIX 7.1 for a new project, so I created a... (11 Replies)
coming from this thread: https://www.unix.com/aix/211107-ibm-power-pseries-open-firmware-boot-vios-powervm-vet-code.html
PowerVM, formerly known as Advanced Power Virtualization (APV), is a chargeable feature of IBM POWER5, POWER6, POWER7, POWER8, and POWER9 servers and is required for support... (0 Replies)
Hello,
After installing on P6 which is POWERVM IVM VIOS enabled (VET CODE D21C77ACD9229817CA1F00002C10004164 )
i get this message
"I/O hosting requires a hosting partition - boot not permitted".
HMC was connected to the machine
then HMC was removed through ASMI
Searching on... (2 Replies)
hello
P6 was managed by HMC, tried to install on it VIOS 2.2.6
and got this error message
Hosting requires a hosting partition -- boot not permitted
vios-4 - imgbb.com
then after creating an lpar in HMC got this message
B2001230
vios-3 - imgbb.com
anyone know how to solve this... (3 Replies)
Discussion started by: filosophizer
3 Replies
LEARN ABOUT CENTOS
ccw_device_start_key
CCW_DEVICE_START_KEY(9) The ccw bus CCW_DEVICE_START_KEY(9)NAME
ccw_device_start_key - start a s390 channel program with key
SYNOPSIS
int ccw_device_start_key(struct ccw_device * cdev, struct ccw1 * cpa, unsigned long intparm, __u8 lpm, __u8 key, unsigned long flags);
ARGUMENTS
cdev
target ccw device
cpa
logical start address of channel program
intparm
user specific interruption parameter; will be presented back to cdev's interrupt handler. Allows a device driver to associate the
interrupt with a particular I/O request.
lpm
defines the channel path to be used for a specific I/O request. A value of 0 will make cio use the opm.
key
storage key to be used for the I/O
flags
additional flags; defines the action to be performed for I/O processing.
DESCRIPTION
Start a S/390 channel program. When the interrupt arrives, the IRQ handler is called, either immediately, delayed (dev-end missing, or
sense required) or never (no IRQ handler registered).
RETURNS
0, if the operation was successful; -EBUSY, if the device is busy, or status pending; -EACCES, if no path specified in lpm is operational;
-ENODEV, if the device is not operational.
CONTEXT
Interrupts disabled, ccw device lock held
AUTHOR
Cornelia Huck <cornelia.huck@de.ibm.com>
Author.
COPYRIGHT Kernel Hackers Manual 3.10 June 2014 CCW_DEVICE_START_KEY(9)