Supporting NIC speed Post: 302743461

10 More Discussions You Might Find Interesting

1. Solaris

How to check Virtual NIC card speed on solaris

Hi, We have a 4 port Sun gigaswift NIC card on our sun fire server. If the card is a physical one I know how to check the settings/speed. But since this is a virtual card with 4 ports , I am not sure as how we can check the settings. Details ----------- root:/> ifconfig -a lo0:...

2. Solaris

Sun box's NIC speed setting

Is there a way to check if my Sun box's network interface card is set to 10 or 100 Mbps? Thanks!

3. IP Networking

NIC speed 100M/full duplex problem

I have a TOSHIBA AS7000 B150 Sun Box I wanted to run it with 100M/full duplex I had added this to the /etc/system file to make to setting permenant So it would be set correctly on reboot. set eri:eri_adv_100fdx_cap=1 set eri:eri_adv_100hdx_cap=0 set eri:eri_adv_autoneg_cap=0 But when I...

4. Filesystems, Disks and Memory

data from blktrace: read speed V.S. write speed

I analysed disk performance with blktrace and get some data: read: 8,3 4 2141 2.882115217 3342 Q R 195732187 + 32 8,3 4 2142 2.882116411 3342 G R 195732187 + 32 8,3 4 2144 2.882117647 3342 I R 195732187 + 32 8,3 4 2145 ...

5. Linux

changing speed of NIC Card in linux

Hi, I would like to know how to change the speed of ethernet card in linux? as it is showing auto-neg using mii-tool -v eth0 and my requirement is 100mbps full duplex. Regards, Manoj

6. Solaris

change NIC speed

how can we change the nic card speed please explain through commands & steps ???? and i want to change NIC speed 100 --1000Mbps and what is full & half duplex gives thanks in advance

7. UNIX for Advanced & Expert Users

Determine the ethernet (NIC) card speed.

Hi, Does anyone know how can I determine the maximum capable speed on a network interface card for different OS like HP, Sun, AIX and Linux. I am aware of the tool "ethtool" which can be used for Linux. Are there any handly commands or /proc files where I can get this info depending on the OS....

8. Solaris

x86 Solaris 10 nic driver added but not attached. NIC is not detected.

I couldn't install my nic in solaris 10. I compiled and added the driver but failed to attach the driver and ifconfig output shows only loopback dev. Please see the following output and tell me whether my nic has been detected and why the driver failed to attach? My nic is detected in linux...

9. Red Hat

I want to tune NIC's rps, rfs and xps value. which NIC device should I modify.

Dear All I want tune my NIC's rps, rfs and xps value. In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1). Here is the question? Which device should I modify ? eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0) Any advice is welcome....

10. Red Hat

Finding speed of NIC Card

Hi, I would like to know how to find out ACTUAL speed of NIC Card. I have used the command ethtool eth0, it is showing supported modes, but what is acutal speed ? how to find out?

LEARN ABOUT DEBIAN

eepro100-diag

EEPRO100-DIAG(8)					      System Manager's Manual						  EEPRO100-DIAG(8)

NAME

       eepro100-diag - EEPROM setup and diagnostic program for Intel EtherExpress Pro100B, and EEPro PCI 10+ ethernet cards.

SYNOPSIS

       eepro100-diag [options]

DESCRIPTION

       eepro100-diag  is a program that you can use to diagnose problems with ethernet cards based the "Speedo3" chip series: the i82557, '558 and
       '559.  These chips are used on the EtherExpress Pro100B, and EEPro PCI 10+.

OPTIONS

       These programs follow the usual GNU command line syntax, with long options starting with  two  dashes  (`-').   A  summary  of  options	is
       included below.

       -h, --help
	      Show summary of options.

       -V, --version
	      Show version of program.

       -v, --verbose
	      Verbose mode.

       -q, --quiet
	      Be very unverbose.

       -# <cardnum>, --card_num <cardnum>
	      Use card number <cardnum>.

       -a, --show_all_registers
	      Print all registers.

       -e, --show-eeprom
	      Dump EEPROM contents to stdout.

       -E, --emergency-rewrite
	      Re-write a corrupted EEPROM.

       -p, --port-base <port>
	      Specify port to use.

       -A, --Advertise <mediaype>
	      Advertise media type. Valid Options are: 10baseT, 100baseT4, 100baseTx, 100baseTx-FD, 100baseTx-HD, 10baseT-FD and 10baseHD.

       -F, --new-interface <interface>
	      Interface  number.  Options that make sense are: 10baseT, 10base2, AUI, 100baseTx, 10baseT-FDX, 100baseTx-FDX, 100baseT4, 100baseFx,
	      100baseFx-FDX, MII and Autosense.

       -H, --new-hwaddress <address>
	      Set card to a new hardware address.

       -m, --show-mii
	      Dump MII management registers.

       -R, --reset
	      Reset the transceiver.

       -T, --test
	      Do register and SRAM test.

       -w, --write-EEPROM <values>
	      Write to the EEPROMS with the specified values. Do not use this, if you do not know what you do!

       -f, --force-detection
	      Try to identify the card, even if it is active.

       -t, --chip-type <card>
	      Explicitly set the chip. To get all valid numbers, run eepro100-diag with the options '-t -1'.

SEE ALSO

       mii-diag(8)

AUTHOR

       eepro100-diag was written and is still maintained by Donald Becker <becker@scyld.com>.  This manual page was  written  by  Alain  Schroeder
       <alain@debian.org>, for the Debian GNU/Linux system (but may be used by others).

								 February 18, 2002						  EEPRO100-DIAG(8)