12-08-2012
Here is a list - RFC 1700 - ports that are registered for use. I don't know where you got your port number info from, but this is a standard list.
http://www.ietf.org/rfc/rfc1700.txt?number=1700
There was a game named 'Doom' back in the early 1990's. The developers got port 666. Do you play doom everyday? No. Does anyone play it on a local LAN? Very close to No. Remote possibility.
Well, then that explains why some aspects of this concept have issues.
Internet Assigned Numbers Authority has a list based on RFC 1700, too. There are other numbers there.
9 More Discussions You Might Find Interesting
1. Cybersecurity
Hello every one.
I work in a LAN with many application server.
Each one use a different port.
What command permit to obtain the number of these port.
thanks (2 Replies)
Discussion started by: hoang
2 Replies
2. UNIX for Dummies Questions & Answers
Hi expert,
I wanted to know in which port my apache is running in solaris box
thanks
Shaan (1 Reply)
Discussion started by: shaan_dmp
1 Replies
3. UNIX for Dummies Questions & Answers
hi all
i want to connect a system,
how can i know the port number of a system. (2 Replies)
Discussion started by: tukuna82
2 Replies
4. Solaris
Hi,
I am Solaris 9 developer and notice that the documentation does not provide a clear notion of the inherent concurrency in routines defined as "Async-Signal-Safe".
Routines defined as "MT-Safe" obviously have the best level of concurrency, compared to normal "Safe" interfaces.
I have... (1 Reply)
Discussion started by: tristan12
1 Replies
5. UNIX for Dummies Questions & Answers
Hi,
Occasionally I am getting the port state in CLOSE_WAIT for long time in the solaris server. I am not sure is it application problem or not. Because we are using port 9009 for Tomcat process in our web application, some time when I start the application, the port 9009 is in CLOSE_WAIT... (0 Replies)
Discussion started by: mgmk.84
0 Replies
6. IP Networking
Hi ,
Currently DELL OMSA SNMP sends data through default udp port 161.I want my custom SNMP MIB also to send data in the same udp port 161.Whether its possible.If yes where to configure .I tried starting my custom MIB in udp port 161,but it throws port already in use.Kindly guide. (0 Replies)
Discussion started by: prabakar4all
0 Replies
7. Red Hat
Hi ,
Currently DELL OMSA SNMP sends data through default udp port 161.I want my custom SNMP MIB also to send data in the same udp port 161.Whether its possible.If yes where to configure .I tried starting my custom MIB in udp port 161,but it throws port already in use.Kindly guide. (1 Reply)
Discussion started by: prabakar4all
1 Replies
8. AIX
Is there any sort of best practice as to how many disks should be assigned to a VIO server? I currently have around 190-ish. All of my VIO servers can see those disks. Can anyone tell me how many you have on your VIO servers? (3 Replies)
Discussion started by: kah00na
3 Replies
9. Solaris
please find the below o/p for your reference
bash-3.00# fcinfo hba-port
HBA Port WWN: 21000024ff295a34
OS Device Name: /dev/cfg/c2
Manufacturer: QLogic Corp.
Model: 375-3356-02
Firmware Version: 05.03.02
FCode/BIOS Version: BIOS: 2.02; fcode: 2.01;... (3 Replies)
Discussion started by: sb200
3 Replies
LEARN ABOUT DEBIAN
debconf-set-selections
DEBCONF-SET-SELECTIONS(1) Debconf DEBCONF-SET-SELECTIONS(1)
NAME
debconf-set-selections - insert new default values into the debconf database
SYNOPSIS
debconf-set-selections file
debconf-get-selections | ssh newhost debconf-set-selections
DESCRIPTION
debconf-set-selections can be used to pre-seed the debconf database with answers, or to change answers in the database. Each question will
be marked as seen to prevent debconf from asking the question interactively.
Reads from a file if a filename is given, otherwise from stdin.
WARNING
Only use this command to seed debconf values for packages that will be or are installed. Otherwise you can end up with values in the
database for uninstalled packages that will not go away, or with worse problems involving shared values. It is recommended that this only
be used to seed the database if the originating machine has an identical install.
DATA FORMAT
The data is a series of lines. Lines beginning with a # character are comments. Blank lines are ignored. All other lines set the value of
one question, and should contain four values, each separated by one character of whitespace. The first value is the name of the package
that owns the question. The second is the name of the question, the third value is the type of this question, and the fourth value (through
the end of the line) is the value to use for the answer of the question.
Alternatively, the third value can be "seen"; then the preseed line only controls whether the question is marked as seen in debconf's
database. Note that preseeding a question's value defaults to marking that question as seen, so to override the default value without
marking a question seen, you need two lines.
Lines can be continued to the next line by ending them with a "" character.
EXAMPLES
# Force debconf priority to critical.
debconf debconf/priority select critical
# Override default frontend to readline, but allow user to select.
debconf debconf/frontend select readline
debconf debconf/frontend seen false
OPTIONS
--verbose, -v
verbose output
--checkonly, -c
only check the input file format, do not save changes to database
SEE ALSO
debconf-get-selections(1) (available in the debconf-utils package)
AUTHOR
Petter Reinholdtsen <pere@hungry.com>
2012-09-10 DEBCONF-SET-SELECTIONS(1)