Hi,
We have a SunFire V880, hooked up with 2 T3 arrays. When ever we issue a reboot command on the system, it hangs at the same place right where it says
syncing file systems done.
To bring it back we shutdown power and it comes clean.
By the way init 6 command works fine.
Has anyone come... (3 Replies)
hello all I have prob with solaris 10 and vmware 5.5, 6.0 that befor it's good work and from yesterday when I try to add new vm in SCSI Controller from vmware it's Don't see any Hard Disk or controller when I used solaris 5 cd-cdrom
and DVD version but when try to make vm with IDE controller... (0 Replies)
Hi,
While we rebooting solaris server ,the system going to Maintenance mode instead of login console.
even we are not able to run fsck command . Thanks in advanced for help.
log attached FYI
Executing last command: boot
Boot device: /pci@83,4000/FJSV,ulsa@2,1/disk@0,0 File and args:... (3 Replies)
Hi,
I have set the date on solaris system , but the the date is changed after rebooting the system . I was suspecting that it could sync with ntp server , so i disabled the NTP and checked, but still whenever i reboot the system , the date that i set is getting changed, Any idea how to come out... (7 Replies)
Hi All,
I had install the solaris 10 into the SUNFIRE V890 server, after installed, it keep rebooting.
I wish to enter the OK mode again, and install back the Solaris 10.
i had try the "break" button and "stop+A" button, but all fail.
kindly advice... (4 Replies)
Hello All,
Solaris 10 which installed in Vmware workstation rebooting automatically and throwing the following error. Looks kernel thread issue, Need experts advice.
Error:
Warning: rpcmod:svc_default_stksize is set more than once in /etc/system/. "set rpcmod:svc_default_stksize =... (0 Replies)
Hello All,
Solaris 10 which installed in Vmware workstation rebooting automatically and throwing the following error. Looks kernel thread issue, Need experts advice.
Error:
Warning: rpcmod:svc_default_stksize is set more than once in /etc/system/. "set rpcmod:svc_default_stksize =... (7 Replies)
Hi all,
How to auto start a snmpd deamon on rebooting a Solaris 5.10 x86 machine.
snmpd's path: /opt/download/net-snmp/sbin
Thank you in advance. (6 Replies)
Hi
I need to know the procedure to add the IP to Solaris 11 zone without rebooting the zone..
I did it on solaris 10 zones but don't know the procedure on solaris 11 zones without rebooting it (1 Reply)
Discussion started by: hb00
1 Replies
LEARN ABOUT DEBIAN
bbackupd
BBACKUPD(8) Box Backup BBACKUPD(8)NAME
bbackupd - Box Backup client daemon
SYNOPSIS
bbackupd [-DFkqvVT] [-c config-file] [-t tag]
DESCRIPTION
bbackupd runs on client computers in the background, finding new files to back up. When it is time for a backup, bbackupd will connect to
the server (bbstored) to upload the files.
A running bbackupd daemon can be controlled with the bbackupctl command, to make it shut down, reload its configuration, or start an
immediate backup.
bbackupd needs to be configured to tell it which files to back up, how often, and to which server (running bbstored). See the Client
Configuration page for more information. For this, you must write a configuration file. You must either place it in the default location,
or tell bbackupd where to find it.
You can check the default location with the -h option. The default on Unix systems is usually /etc/box/bbackupd.conf. On Windows systems,
it is bbackupd.conf in the same directory where bbackupd.exe is located. If bbackupd cannot find or read the configuration file, it will
log an error message and exit.
bbackupd usually writes log messages to the system logs, using the facility local5, which you can use to filter them to send them to a
separate file. It can also write them to the console, see options below. If bbackupd is not doing what you expect, please check the logs
first of all.
Options
-c config-file
Use the specified configuration file. If -c is omitted, the last argument is the configuration file. If none is specified, the default
is used (see above).
-D
Debugging mode. Do not fork into the background (do not run as a daemon). Not available on Windows.
-F
No-fork mode. Same as -D for bbackupd. Not available on Windows.
-k
Keep console open after fork, keep writing log messages to it. Not available on Windows.
-q
Run more quietly. Reduce verbosity level by one. Available levels are NOTHING, FATAL, ERROR, WARNING, NOTICE, INFO, TRACE, EVERYTHING.
Default level is NOTICE in non-debugging builds. Use once to drop to WARNING level, twice for ERROR level, four times for no logging at
all.
-v
Run more verbosely. Increase verbosity level by one. Use once to raise to INFO level, twice for TRACE level, three times for EVERYTHING
(currently the same as TRACE).
-V
Run at maximum verbosity (EVERYTHING level).
-t tag
Tag each console message with specified marker. Mainly useful in testing when running multiple daemons on the same console.
-T
Timestamp each line of console output.
FILES
/etc/box/bbackupd.conf
SEE ALSO bbackupd.conf(5), bbackupd-config(8), bbackupctl(8)AUTHORS
Ben Summers
Per Thomsen
James O'Gorman
Box Backup 0.11 10/28/2011 BBACKUPD(8)