12-07-2012
So are the consoles cabled directly to each server or are they somehow pushed through a network, perhaps with a small box plugged in the console port and the network? I've seen HP servers like this ages ago.
I must admit that most of my servers are all virtual, so the supervising partition beastie (HMC or VIO for AIX) give you a virtual terminal, so that's not a worry. The nearest I get is for those servers that have a serial port only, but we have a Cyclades terminal server in place. It takes all the serial cables in centrally and we can connect by telnet to a specific port. I only have to ensure that the ethernet port on the Cyclades server is up to scratch.
Could you describe a bit more what you have for a typical server/console?
Thanks in advance,
Robin
Liverpool/Blackburn
UK
10 More Discussions You Might Find Interesting
1. Solaris
Hi,
We have a 4 port Sun gigaswift NIC card on our sun fire server.
If the card is a physical one I know how to check the settings/speed. But since this is a virtual card with 4 ports , I am not sure as how we can check the settings.
Details
-----------
root:/> ifconfig -a
lo0:... (3 Replies)
Discussion started by: pray44u
3 Replies
2. Solaris
Is there a way to check if my Sun box's network interface card is set to 10 or 100 Mbps?
Thanks! (1 Reply)
Discussion started by: FredSmith
1 Replies
3. IP Networking
I have a TOSHIBA AS7000 B150 Sun Box
I wanted to run it with 100M/full duplex
I had added this to the /etc/system file to make to setting permenant So it would be set correctly on reboot.
set eri:eri_adv_100fdx_cap=1
set eri:eri_adv_100hdx_cap=0
set eri:eri_adv_autoneg_cap=0
But when I... (4 Replies)
Discussion started by: AirWalker83
4 Replies
4. Filesystems, Disks and Memory
I analysed disk performance with blktrace and get some data:
read:
8,3 4 2141 2.882115217 3342 Q R 195732187 + 32
8,3 4 2142 2.882116411 3342 G R 195732187 + 32
8,3 4 2144 2.882117647 3342 I R 195732187 + 32
8,3 4 2145 ... (1 Reply)
Discussion started by: W.C.C
1 Replies
5. Linux
Hi,
I would like to know how to change the speed of ethernet card in linux? as it is showing auto-neg using mii-tool -v eth0
and my requirement is 100mbps full duplex.
Regards,
Manoj (3 Replies)
Discussion started by: manoj.solaris
3 Replies
6. Solaris
how can we change the nic card speed
please explain through commands & steps ????
and i want to change NIC speed 100 --1000Mbps
and what is full & half duplex gives
thanks in advance (6 Replies)
Discussion started by: wkbn86
6 Replies
7. UNIX for Advanced & Expert Users
Hi,
Does anyone know how can I determine the maximum capable speed on a network interface card for different OS like HP, Sun, AIX and Linux.
I am aware of the tool "ethtool" which can be used for Linux. Are there any handly commands or /proc files where I can get this info depending on the OS.... (3 Replies)
Discussion started by: devtakh
3 Replies
8. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
9. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
10. Red Hat
Hi,
I would like to know how to find out ACTUAL speed of NIC Card.
I have used the command ethtool eth0, it is showing supported modes,
but what is acutal speed ? how to find out? (4 Replies)
Discussion started by: manoj.solaris
4 Replies