Hi,
We have a 4 port Sun gigaswift NIC card on our sun fire server.
If the card is a physical one I know how to check the settings/speed. But since this is a virtual card with 4 ports , I am not sure as how we can check the settings.
Details
-----------
root:/> ifconfig -a
lo0:... (3 Replies)
I have a TOSHIBA AS7000 B150 Sun Box
I wanted to run it with 100M/full duplex
I had added this to the /etc/system file to make to setting permenant So it would be set correctly on reboot.
set eri:eri_adv_100fdx_cap=1
set eri:eri_adv_100hdx_cap=0
set eri:eri_adv_autoneg_cap=0
But when I... (4 Replies)
I analysed disk performance with blktrace and get some data:
read:
8,3 4 2141 2.882115217 3342 Q R 195732187 + 32
8,3 4 2142 2.882116411 3342 G R 195732187 + 32
8,3 4 2144 2.882117647 3342 I R 195732187 + 32
8,3 4 2145 ... (1 Reply)
Hi,
I would like to know how to change the speed of ethernet card in linux? as it is showing auto-neg using mii-tool -v eth0
and my requirement is 100mbps full duplex.
Regards,
Manoj (3 Replies)
how can we change the nic card speed
please explain through commands & steps ????
and i want to change NIC speed 100 --1000Mbps
and what is full & half duplex gives
thanks in advance (6 Replies)
Hi,
Does anyone know how can I determine the maximum capable speed on a network interface card for different OS like HP, Sun, AIX and Linux.
I am aware of the tool "ethtool" which can be used for Linux. Are there any handly commands or /proc files where I can get this info depending on the OS.... (3 Replies)
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Hi,
I would like to know how to find out ACTUAL speed of NIC Card.
I have used the command ethtool eth0, it is showing supported modes,
but what is acutal speed ? how to find out? (4 Replies)
Discussion started by: manoj.solaris
4 Replies
LEARN ABOUT DEBIAN
console
CONSOLE(4) Linux User's Manual CONSOLE(4)NAME
console - console terminal and virtual consoles
DESCRIPTION
A Linux system has up to 63 virtual consoles (character devices with major number 4 and minor number 1 to 63), usually called /dev/ttyn
with 1 <= n <= 63. The current console is also addressed by /dev/console or /dev/tty0, the character device with major number 4 and minor
number 0. The device files /dev/* are usually created using the script MAKEDEV, or using mknod(1), usually with mode 0622 and owner
root.tty.
Before kernel version 1.1.54 the number of virtual consoles was compiled into the kernel (in tty.h: #define NR_CONSOLES 8) and could be
changed by editing and recompiling. Since version 1.1.54 virtual consoles are created on the fly, as soon as they are needed.
Common ways to start a process on a console are: (a) tell init(8) (in inittab(5)) to start a getty(8) on the console; (b) ask open(1) to
start a process on the console; (c) start X - it will find the first unused console, and display its output there. (There is also the
ancient doshell(8).)
Common ways to switch consoles are: (a) use Alt+Fn or Ctrl+Alt+Fn to switch to console n; AltGr+Fn might bring you to console n+12 [here
Alt and AltGr refer to the left and right Alt keys, respectively]; (b) use Alt+RightArrow or Alt+LeftArrow to cycle through the presently
allocated consoles; (c) use the program chvt(1). (The key mapping is user settable, see loadkeys(1); the above mentioned key combinations
are according to the default settings.)
The command deallocvt(1) (formerly disalloc) will free the memory taken by the screen buffers for consoles that no longer have any associ-
ated process.
PROPERTIES
Consoles carry a lot of state. I hope to document that some other time. The most important fact is that the consoles simulate vt100 termi-
nals. In particular, a console is reset to the initial state by printing the two characters ESC c. All escape sequences can be found in
console_codes(4).
FILES
/dev/console
/dev/tty*
SEE ALSO charsets(4), console_codes(4), console_ioctl(4), mknod(1), tty(4), ttys(4), getty(8), init(8), chvt(1), open(1), deallocvt(1), loadkeys(1),
resizecons(8), consolechars(8), mapscrn(8).
Console tools 28 Oct 1997 CONSOLE(4)