12-07-2012
Usually, this is more a question of having the faster NIC. It has been decades since system infrastructure could not handle 100M/64 double words per second (640 nanosecond RAM cycles) peak. Software, of course, does not care.
10 More Discussions You Might Find Interesting
1. Solaris
Hi,
We have a 4 port Sun gigaswift NIC card on our sun fire server.
If the card is a physical one I know how to check the settings/speed. But since this is a virtual card with 4 ports , I am not sure as how we can check the settings.
Details
-----------
root:/> ifconfig -a
lo0:... (3 Replies)
Discussion started by: pray44u
3 Replies
2. Solaris
Is there a way to check if my Sun box's network interface card is set to 10 or 100 Mbps?
Thanks! (1 Reply)
Discussion started by: FredSmith
1 Replies
3. IP Networking
I have a TOSHIBA AS7000 B150 Sun Box
I wanted to run it with 100M/full duplex
I had added this to the /etc/system file to make to setting permenant So it would be set correctly on reboot.
set eri:eri_adv_100fdx_cap=1
set eri:eri_adv_100hdx_cap=0
set eri:eri_adv_autoneg_cap=0
But when I... (4 Replies)
Discussion started by: AirWalker83
4 Replies
4. Filesystems, Disks and Memory
I analysed disk performance with blktrace and get some data:
read:
8,3 4 2141 2.882115217 3342 Q R 195732187 + 32
8,3 4 2142 2.882116411 3342 G R 195732187 + 32
8,3 4 2144 2.882117647 3342 I R 195732187 + 32
8,3 4 2145 ... (1 Reply)
Discussion started by: W.C.C
1 Replies
5. Linux
Hi,
I would like to know how to change the speed of ethernet card in linux? as it is showing auto-neg using mii-tool -v eth0
and my requirement is 100mbps full duplex.
Regards,
Manoj (3 Replies)
Discussion started by: manoj.solaris
3 Replies
6. Solaris
how can we change the nic card speed
please explain through commands & steps ????
and i want to change NIC speed 100 --1000Mbps
and what is full & half duplex gives
thanks in advance (6 Replies)
Discussion started by: wkbn86
6 Replies
7. UNIX for Advanced & Expert Users
Hi,
Does anyone know how can I determine the maximum capable speed on a network interface card for different OS like HP, Sun, AIX and Linux.
I am aware of the tool "ethtool" which can be used for Linux. Are there any handly commands or /proc files where I can get this info depending on the OS.... (3 Replies)
Discussion started by: devtakh
3 Replies
8. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
9. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
10. Red Hat
Hi,
I would like to know how to find out ACTUAL speed of NIC Card.
I have used the command ethtool eth0, it is showing supported modes,
but what is acutal speed ? how to find out? (4 Replies)
Discussion started by: manoj.solaris
4 Replies
FITYK(1) General Commands Manual FITYK(1)
NAME
fityk - non-linear curve fitting and data analysis
SYNOPSIS
fityk [OPTION]... [FILE]...
cfityk [OPTION]... [FILE]...
DESCRIPTION
This manpage documents briefly the fityk and cfityk programs for nonlinear fitting of analytical functions (especially peak-shaped) to data
(usually experimental data). In other words, for nonlinear peak separation and analysis.
It was developed for analyzing diffraction patterns, but can be also used in other fields, since concepts and operations specific for crys-
tallography are separated from the rest of the program.
Fityk offers various nonlinear fitting methods, subtracting background, calibrating data, easy placement of peaks and changing peak parame-
ters, automation of common tasks with scripts, and much more. The main advantage of the program is a flexibility - parameters of peaks can
be arbitrarily binded with each other, eg. width of peak can be an independent variable, can be the same as width of other peak or can be
given by complicated - common for all peaks - formula.
The program comes in two versions: fityk , the GUI version and cfityk , the command line version.
A user manual for fityk and cfityk can be found in /usr/share/doc/fityk/html/fityk-manual.html.
OPTIONS
-h, --help
Print the usage and exit.
-V, --version
Print the version number and exit.
Use --help to see the full list of options.
AUTHOR
This manual page was written by Carlo Segre <segre@iit.edu> and updated by Marcin Wojdyr.
January 8, 2006 FITYK(1)