Sponsored Content
Full Discussion: Supporting NIC speed
Operating Systems Solaris Supporting NIC speed Post 302741059 by solaris_1977 on Friday 7th of December 2012 10:55:03 AM
Old 12-07-2012
Supporting NIC speed

Hi,
I have few Solaris (9 and 10) servers, whose consoles are running on 10 MBPs. Now, Network team is changing their switch, which doesn't support 10 MBPs and we need to check if console all of those servers will support 100MBPs or more.
Is there any way to check supported (or maximum supported) speed on console. Most of them are sc, rsc and ilom.
Regards

Last edited by solaris_1977; 12-07-2012 at 12:12 PM..
 

10 More Discussions You Might Find Interesting

1. Solaris

How to check Virtual NIC card speed on solaris

Hi, We have a 4 port Sun gigaswift NIC card on our sun fire server. If the card is a physical one I know how to check the settings/speed. But since this is a virtual card with 4 ports , I am not sure as how we can check the settings. Details ----------- root:/> ifconfig -a lo0:... (3 Replies)
Discussion started by: pray44u
3 Replies

2. Solaris

Sun box's NIC speed setting

Is there a way to check if my Sun box's network interface card is set to 10 or 100 Mbps? Thanks! (1 Reply)
Discussion started by: FredSmith
1 Replies

3. IP Networking

NIC speed 100M/full duplex problem

I have a TOSHIBA AS7000 B150 Sun Box I wanted to run it with 100M/full duplex I had added this to the /etc/system file to make to setting permenant So it would be set correctly on reboot. set eri:eri_adv_100fdx_cap=1 set eri:eri_adv_100hdx_cap=0 set eri:eri_adv_autoneg_cap=0 But when I... (4 Replies)
Discussion started by: AirWalker83
4 Replies

4. Filesystems, Disks and Memory

data from blktrace: read speed V.S. write speed

I analysed disk performance with blktrace and get some data: read: 8,3 4 2141 2.882115217 3342 Q R 195732187 + 32 8,3 4 2142 2.882116411 3342 G R 195732187 + 32 8,3 4 2144 2.882117647 3342 I R 195732187 + 32 8,3 4 2145 ... (1 Reply)
Discussion started by: W.C.C
1 Replies

5. Linux

changing speed of NIC Card in linux

Hi, I would like to know how to change the speed of ethernet card in linux? as it is showing auto-neg using mii-tool -v eth0 and my requirement is 100mbps full duplex. Regards, Manoj (3 Replies)
Discussion started by: manoj.solaris
3 Replies

6. Solaris

change NIC speed

how can we change the nic card speed please explain through commands & steps ???? and i want to change NIC speed 100 --1000Mbps and what is full & half duplex gives thanks in advance (6 Replies)
Discussion started by: wkbn86
6 Replies

7. UNIX for Advanced & Expert Users

Determine the ethernet (NIC) card speed.

Hi, Does anyone know how can I determine the maximum capable speed on a network interface card for different OS like HP, Sun, AIX and Linux. I am aware of the tool "ethtool" which can be used for Linux. Are there any handly commands or /proc files where I can get this info depending on the OS.... (3 Replies)
Discussion started by: devtakh
3 Replies

8. Solaris

x86 Solaris 10 nic driver added but not attached. NIC is not detected.

I couldn't install my nic in solaris 10. I compiled and added the driver but failed to attach the driver and ifconfig output shows only loopback dev. Please see the following output and tell me whether my nic has been detected and why the driver failed to attach? My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies

9. Red Hat

I want to tune NIC's rps, rfs and xps value. which NIC device should I modify.

Dear All I want tune my NIC's rps, rfs and xps value. In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1). Here is the question? Which device should I modify ? eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0) Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies

10. Red Hat

Finding speed of NIC Card

Hi, I would like to know how to find out ACTUAL speed of NIC Card. I have used the command ethtool eth0, it is showing supported modes, but what is acutal speed ? how to find out? (4 Replies)
Discussion started by: manoj.solaris
4 Replies
cvcredir(7D)							      Devices							      cvcredir(7D)

NAME
cvcredir - virtual console redirection driver DESCRIPTION
The cvcredir virtual console redirection driver is a STREAMS-based pseudo driver that supports the network console provided on some plat- forms. The cvcredir driver interfaces with the virtual console driver cvc(7D), and the virtual console daemon, cvcd(1M). The cvcredir driver receives console output from cvc and passes it to cvcd. It receives console input from cvcd and passes it to cvc. ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Architecture |Sun Enterprise 10000 | | |servers, Sun Fire 15K | | |servers | +-----------------------------+-----------------------------+ |Availability |SUNWcvc.u | +-----------------------------+-----------------------------+ SEE ALSO
cvcd(1M), attributes(5), console(7D), cvc(7D) Sun Enterprise 10000 SSP Reference Manual Sun System Management Services (SMS) Reference Manual SunOS 5.11 15 Sep 2000 cvcredir(7D)
All times are GMT -4. The time now is 08:01 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy