I tried to attach the bdf and inq reports.
Please see that few disks are under ASM.
I am trying to figure out the steps I need to take while cutting over to the new LUNS.
Hi, I'm going to be involved in a migration of SAN islands to one big SAN. I've not worked with SANs before and I'm not sure how to approach this. I suspect the disk devices on the HP servers are going to change, when the EVA's and servers are plugged into this new Cisco 9509 switch.
Any... (0 Replies)
Hi everyone,
I wonder if I can canvas any opinions or thoughts (good or bad) on SAN attaching a SUN V880/490 to an EMC Clarion SAN?
At the moment the 880 is using 12 internal FC-AL disks as a db server and seems to be doing a pretty good job. It is not I/O, CPU or Memory constrained and the... (2 Replies)
hi all
just installed the netsec.options.tcpwrapper from expansion pack, which used to be a rpm, for my aix 6.1 test box.
it is so unpredictable. i set up the hosts.deny as suggested for all and allow the sshd for specific ip addresses/hostnames.
the tcpdchk says the hosts allowed and... (0 Replies)
I am going to do a SAN Array migration and need the sequence of steps required on the Solaris cluster before moving the old array luns to new array luns.
Here are the steps and I need info on the bold points:( I might even be wrong on the sequence of steps please correct me if I am wrong)
1.... (0 Replies)
Hi all,
We are migrating our SAN storage from HSV360 to 3PAR. The system runs aix 6.1 version with HACMP.
Please let me know what are requirements from OS side and how are the data copied to the new disks. (10 Replies)
Hi,
I am very new to HP-UX, and we're going to be doing a SAN migration.
We're going to take down the machine, and zone it to the new SAN.
My question is, will the device names change and will that interfere with the LVM?
If the new disks come in with different device names, how would I... (3 Replies)
I have an IBM blade running RHEL 5.4 server, connected to two Hitachi SANs using common fibre cards & Brocade switches. It has two volume groups made from old SAN LUNs. The old SAN needs to be retired so we allocated LUNs from the new SAN, discovered the LUNs as multipath disks (4 paths) and grew... (4 Replies)
I'm New to AIX / VIOS
We're doing a FC switch cutover on an ibm device, connected via SAN.
How do I tell if one path to my remote disk is lost? (aix lvm)
How do I tell when my link is down on my HBA port?
Appreciate your help, very much! (4 Replies)
I am working on VM host and collecting data to identify the type of storage attached to the server which will be migrated to VNX.
it has one ldom created on it
luxadm probe output ---
No Network Array enclosures found in /dev/es
Found Fibre Channel device(s):
Node... (7 Replies)
Am trying to copy a tar file onto a series of remote hosts and untar it at the destination. Need to do this without having to do multiple ssh.
Actions to perform within a single ssh session via shell script
- copy a file
- untar at destination (remote host)
OS : Linux RHEL6 (3 Replies)
Discussion started by: sankasu
3 Replies
LEARN ABOUT ULTRIX
iostat
iostat(1) General Commands Manual iostat(1)Name
iostat - report I/O statistics
Syntax
iostat [ -c ] [ -t ] [ disknames ] [ interval ] [ count ]
Description
The command reports I/O statistics for terminals, disks and cpus. For terminals the number of input and output characters are counted.
For disks the number of 512 byte blocks per second and number of transfers per second are displayed. For cpus, it provides the percentage
of time the system has spent in user mode, in user mode running low priority (niced) processes, in system mode, and idling. On multipro-
cessor systems these cpu statistics represent a cumulative summary of all the cpus.
The optional disknames argument causes disk statistics to be displayed for the specified disks. If this argument is not specified then
disk statistics will be displayed for the first 3 disks only.
The optional interval argument causes to report once each interval seconds. The first report is for all time since a reboot and each sub-
sequent report is for the last interval only.
The optional count argument restricts the number of reports.
Options-c Displays the percentage of time each cpu spent in user mode, running low priority (nice'd) processes, in system mode, and idling.
-t Displays the number of characters read from and written to terminals.
Examples
This example will cause cpu and disk statistics for the 5 disks ra0, ra1, ra2, ra3, and ra4.
iostat ra0 ra1 ra2 ra3 ra4
This example will cause cpu, terminal, and disk statistics for ra0 to be displayed and updated every 2 seconds.
iostat -t ra0 2
FilesSee Alsovmstat(1), cpustat(1)iostat(1)