11-16-2012
Thank you jgt, I'll try that with booting the drive with different hardware. Sadly, installing another version of it is a non-starter as I don't have any SCO disks. But I'll definitely try to boot it to new hardware.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
# grep "Jul 3" syslog.messages | more
Jul 3 00:16:03 www3 CPU3: NOTICE: HTFS: No space on dev hd (1/42)
Jul 3 00:16:08 www3 CPU3: NOTICE: HTFS: No space on dev hd (1/42)
Jul 3 00:17:01 www3 CPU2: NOTICE: HTFS: No space on dev hd (1/42)
Jul 3 00:17:06 www3 syslogd: /usr/adm/debug: No space... (1 Reply)
Discussion started by: Cameron
1 Replies
2. UNIX for Dummies Questions & Answers
Hello all. I am receiving this message on the console of a SCO Openserver 5.0.7 server. The hardware is IBM, running mirrored SCSI drives with a hot-swap spare off of an IBM Serveraid controller. I suspect that some permutation of fsck can help me resolve whatever is causing the error, but I am... (0 Replies)
Discussion started by: DoublePanic
0 Replies
3. UNIX for Advanced & Expert Users
If somebody solve this error please help me!
Thanks in advance! :confused: (7 Replies)
Discussion started by: FCollet
7 Replies
4. SCO
I have a 17GB SCSI disk in an SCO 5.0.6 server and it's running out of space because of a growing database on the disk. Consequently I would like to upgrade the 17GB to a 74GB disk and extend the partition.
First off, is partition extension available under HTFS - I know this is an old... (1 Reply)
Discussion started by: carribey
1 Replies
5. UNIX for Dummies Questions & Answers
i am about to install oracle on my solaris x86-64
This installation require 4Gb space and i qish to do this installation on the directory
/u01/app/oracle
The following was my approch
mkdir -p /u01/app/oracle
i then use the command below to see if there is enough space
# df -h... (6 Replies)
Discussion started by: seyiisq
6 Replies
6. Solaris
Hi all,
currently , my root filesystem already reach 90 ++%
I already add more cylinder in the root partition as below
Part Tag Flag Cylinders Size Blocks
0 root wm 67 - 5086 38.46GB (5020/0/0) 80646300
1 swap wu 1 - ... (11 Replies)
Discussion started by: SmartAntz
11 Replies
7. UNIX for Dummies Questions & Answers
Hi,
How to mount HTFS FS (from SCO UNIX) under linux?
Best regards.
where is link: htfs_fs-0.01alpha.tar.bz2 (2 Replies)
Discussion started by: EMREZ
2 Replies
8. UNIX for Dummies Questions & Answers
Hi,
I wanted to find out that in my database server which filesystems are shared storage and which filesystems are local. Like when I use df -k, it shows "filesystem" and "mounted on" but I want to know which one is shared and which one is local.
Please tell me the commands which I can run... (2 Replies)
Discussion started by: kamranjalal
2 Replies
9. Solaris
Hi guys!
Could you tell me what's the difference of filesystem of Solaris to filesystem of Windows? I need to compare both.
I have read some over the net but it's so much technical. Could you explain it in a more simpler term? I am new to Solaris. Hope you help me guys.
Thanks! (4 Replies)
Discussion started by: arah
4 Replies
10. AIX
Dear all,
We are facing prolem when we are going to mount AIX filesystem, the system returned the following error
0506-307The AFopen call failed
: A file or directory in the path name does not exist.
But when we ls filesystems in the /etc/ directory it show
-rw-r--r-- 0 root ... (2 Replies)
Discussion started by: m_raheelahmed
2 Replies
LEARN ABOUT MINIX
addbadsec
addbadsec(1M) System Administration Commands addbadsec(1M)
NAME
addbadsec - map out defective disk blocks
SYNOPSIS
addbadsec [-p] [ -a blkno [blkno...]] [-f filename] raw_device
DESCRIPTION
addbadsec is used by the system administrator to map out bad disk blocks. Normally, these blocks are identified during surface analysis,
but occasionally the disk subsystem reports unrecoverable data errors indicating a bad block. A block number reported in this way can be
fed directly into addbadsec, and the block will be remapped. addbadsec will first attempt hardware remapping. This is supported on SCSI
drives and takes place at the disk hardware level. If the target is an IDE drive, then software remapping is used. In order for software
remapping to succeed, the partition must contain an alternate slice and there must be room in this slice to perform the mapping.
It should be understood that bad blocks lead to data loss. Remapping a defective block does not repair a damaged file. If a bad block
occurs to a disk-resident file system structure such as a superblock, the entire slice might have to be recovered from a backup.
OPTIONS
The following options are supported:
-a Adds the specified blocks to the hardware or software map. If more than one block number is specified, the entire list should be
quoted and block numbers should be separated by white space.
-f Adds the specified blocks to the hardware or software map. The bad blocks are listed, one per line, in the specified file.
-p Causes addbadsec to print the current software map. The output shows the defective block and the assigned alternate. This option
cannot be used to print the hardware map.
OPERANDS
The following operand is supported:
raw_device The address of the disk drive (see FILES).
FILES
The raw device should be /dev/rdsk/c?[t?]d?p0. See disks(1M) for an explanation of SCSI and IDE device naming conventions.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Architecture |x86 |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO
disks(1M), diskscan(1M), fdisk(1M), fmthard(1M), format(1M), attributes(5)
NOTES
The format(1M) utility is available to format, label, analyze, and repair SCSI disks. This utility is included with the addbadsec,
diskscan(1M), fdisk(1M), and fmthard(1M) commands available for x86. To format an IDE disk, use the DOS "format" utility; however, to
label, analyze, or repair IDE disks on x86 systems, use the Solaris format(1M) utility.
SunOS 5.10 24 Feb 1998 addbadsec(1M)