11-16-2012
Non-interactive fdisk partition in script
Hi,
How can I run fdisk partition in a script without interactive input?
In manual procedure, I run fdisk device, select n, select p, presess enter for default start number (1), press enter to default end number, then select w for writing to the partition table. The command looks like "fdisk -u -p ..... /dev/device"
Thanks.
Kind regards.
10 More Discussions You Might Find Interesting
1. Solaris
I have two disks on a sun blade 100. I just installed a solaris8 on the first disk. The installation was successful. But the problem is now I lost all data / partition on my second hard disk.
The possible reason could be:
1. I used default web start install. During the installation I didn't... (2 Replies)
Discussion started by: motor98
2 Replies
2. UNIX for Dummies Questions & Answers
Hello everyone -
Please forgive me if I violate the forum's etiquette as this is my very first post. I'm posting this on both the dummies and the advance section with the hope for any responses.
I stumbled on this forum while frantically looking for an answer to a dumb, ignorant thing I did... (2 Replies)
Discussion started by: kevindoman
2 Replies
3. UNIX for Advanced & Expert Users
Hello everyone -
Please forgive me if I violate the forum's etiquette as this is my very first post. I'm posting this on both the dummies and the advance section with the hope for any responses.
I stumbled on this forum while frantically looking for an answer to a dumb, ignorant thing I did... (5 Replies)
Discussion started by: kevindoman
5 Replies
4. Homework & Coursework Questions
Q. Write a script that behaves both in interactive and non interactive mode. When no arguments are supplied it picks up each C program from the directory and prints first 10 lines.
It then prompts for deletion of the file.
If user supplies arguments with the script , then it works on those files... (1 Reply)
Discussion started by: rits
1 Replies
5. Homework & Coursework Questions
Q. Write a script that behaves both in interactive and non interactive mode. When no arguments are supplied it picks up each C program from the directory and prints first 10 lines.
It then prompts for deletion of the file.
If user supplies arguments with the script , then it works on those files... (8 Replies)
Discussion started by: rits
8 Replies
6. Shell Programming and Scripting
Greetings gurus
I have this simple scripts
#!/bin/bash
find /kl1/CTT/TQI_001/330_spike/sz00/latcon1/ -type d -name "*.dig" > data_schema
find /kl1/CTT/TQI_001/330_spike/sz00/latcon1/ -type d -name "*.dig" >> data_schema
<data.schema awk '{print NR, "inVol=" $0, "setDt=4000",... (1 Reply)
Discussion started by: Marjan
1 Replies
7. Shell Programming and Scripting
I'm using
fdisk -l > myFile
to get the file size of the device in a file where I want the output
but one line always go to the terminal and make my interface look ugly:
Disk /dev/sda doesn't contain a valid partition table
How do I stop this line from going to the command line with a... (2 Replies)
Discussion started by: darkstarxor
2 Replies
8. Filesystems, Disks and Memory
Hello,
I have a RHEL system with two 500GB hard drives in RAID 1 (I think hardware, but not 100% certain - any way to tell?).
It looks like it was just set up in default configuration with a small boot partition and one huge partition for the rest, which composes a LVM volume.
I want... (1 Reply)
Discussion started by: builder88
1 Replies
9. Red Hat
Hello,
I have been going through our environment and I see we have a few servers with LVM's setup and the file system type is still set to "83" within fdisk. If I change this to "8e", will it hurt the data or cause any loss? I need to know for sure before I make the change. (1 Reply)
Discussion started by: s ladd
1 Replies
10. BSD
Hello,
MBR partition table made by linux fdisk looks certainly not correct when printed by openbsd fdisk:
Partition table created on linux (centos 6.3):
# fdisk -l /dev/sdc
Disk /dev/sdc: 10.7 GB, 10737418240 bytes
255 heads, 63 sectors/track, 1305 cylinders
Units = cylinders of 16065 *... (2 Replies)
Discussion started by: vilius
2 Replies
FDISK(8) System Manager's Manual FDISK(8)
NAME
fdisk - partition a hard disk [IBM]
SYNOPSIS
fdisk [-hm] [-sn] [file]
OPTIONS
-h Number of disk heads is m
-s Number of sectors per track is n
EXAMPLES
fdisk /dev/hd0 # Examine disk partitions
fdisk -h9 /dev/hd0 # Examine disk with 9 heads
DESCRIPTION
When fdisk starts up, it reads in the partition table and displays it. It then presents a menu to allow the user to modify partitions,
store the partition table on a file, or load it from a file. Partitions can be marked as MINIX, DOS or other, as well as active or not.
Using fdisk is self-explanatory. However, be aware that repartitioning a disk will cause information on it to be lost. Rebooting the sys-
tem immediately is mandatory after changing partition sizes and parameters. MINIX, XENIX, PC-IX, and MS-DOS all have different partition
numbering schemes. Thus when using multiple systems on the same disk, be careful.
Note that MINIX, unlike MS-DOS , cannot access the last sector in a partition with an odd number of sectors. The reason that odd partition
sizes do not cause a problem with MS-DOS is that MS-DOS allocates disk space in units of 512-byte sectors, whereas MINIX uses 1K blocks.
Fdisk has a variety of other features that can be seen by typing h.
Fdisk normally knows the geometry of the device by asking the driver. You can use the -h and -s options to override the numbers found.
SEE ALSO
part(8).
FDISK(8)