11-15-2012
and what i must use?
how modified my READ function? thanks
9 More Discussions You Might Find Interesting
1. Linux
Hi All,
I am a begineer in Linux, I have 4 ports and 3 are operational port 1,port 2 and port 4 (when I plug in serial device I can see it working) but port 3 seems it is not working.
I am sure the hardware is fine.
when I give command
dmesg | grep tty
I get,
serial 8250:ttyS0 at... (0 Replies)
Discussion started by: vr_82
0 Replies
2. SCO
dear sir,
pls. can you help me ? , my os is unix sco 5.0.4 and ,server dat derive (1,4gb)
not working, now i want to transfer my server data in other machine (unix/other possible) by serial port/other port comminication.
thanks
pankaj raval (2 Replies)
Discussion started by: pankajbraval
2 Replies
3. Programming
I have problem with C programming. I want to send & receive data through serial communication. I send data(command) to device to get data from device but when receive data, it can't get altogether of data.
It get only some data. What should I do to get altogether of data?
If all of... (7 Replies)
Discussion started by: noppon_s
7 Replies
4. Shell Programming and Scripting
Hi,
I have a external board connected to my serial port. I need to execute "shutdown -r now" command when system boot up. When system boots up it requires a username ans password. Then I need to run my command. I can use rc script but that is rebooting system before it asks for username and... (0 Replies)
Discussion started by: charlie.arya
0 Replies
5. Solaris
Hi Everyone,
In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
Discussion started by: bobby320
3 Replies
6. Programming
hey frns pls help me out !!
i hav a code of c that i have to include in my project.
i am using a device (geomeda) that has unix based OS. it also support SIM card for connecting to server . I need to send SMS to user from this device..
below code is not working .. i am unable to send sms and the... (7 Replies)
Discussion started by: yashwantkumar
7 Replies
7. Programming
Hi
I try to communicate with a GSM modem, from C, for sending SMS.
I use standart AT-commands.
Working well with terminal.
There is no problem writing ti the port.
But when I try to read I only get a echo, I write "ATI" and get "ATI" back, I should get somthing like "SIEMENS 35... (4 Replies)
Discussion started by: dmiller
4 Replies
8. Debian
Dear List -
I am trying to capture data from a serial port and write it to a file.
/var/www$ cat /dev/ttyS0 > scale_value.html
cat: /dev/ttyS0: Device or resource busy
/var/www# cat /proc/tty/driver/serial
serinfo:1.0 driver revision:
0: uart:16550A port:000003F8 irq:4 tx:90... (11 Replies)
Discussion started by: Meow613
11 Replies
9. Solaris
Hello,
I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build.
The first part is what confuses me -the cabling.
I am coming from a Windows machine (w/appropriate... (5 Replies)
Discussion started by: joboy
5 Replies
LEARN ABOUT OPENDARWIN
start_transaction
START
TRANSACTION(7) SQL Commands START TRANSACTION(7)
NAME
START TRANSACTION - start a transaction block
SYNOPSIS
START TRANSACTION [ transaction_mode [, ...] ]
where transaction_mode is one of:
ISOLATION LEVEL { SERIALIZABLE | REPEATABLE READ | READ COMMITTED | READ UNCOMMITTED }
READ WRITE | READ ONLY
DESCRIPTION
This command begins a new transaction block. If the isolation level or read/write mode is specified, the new transaction has those charac-
teristics, as if SET TRANSACTION [set_transaction(7)] was executed. This is the same as the BEGIN [begin(7)] command.
PARAMETERS
Refer to SET TRANSACTION [set_transaction(7)] for information on the meaning of the parameters to this statement.
COMPATIBILITY
In the standard, it is not necessary to issue START TRANSACTION to start a transaction block: any SQL command implicitly begins a block.
PostgreSQL's behavior can be seen as implicitly issuing a COMMIT after each command that does not follow START TRANSACTION (or BEGIN), and
it is therefore often called ``autocommit''. Other relational database systems might offer an autocommit feature as a convenience.
The SQL standard requires commas between successive transaction_modes, but for historical reasons PostgreSQL allows the commas to be omit-
ted.
See also the compatibility section of SET TRANSACTION [set_transaction(7)].
SEE ALSO
BEGIN [begin(7)], COMMIT [commit(7)], ROLLBACK [rollback(7)], SAVEPOINT [savepoint(7)], SET TRANSACTION [set_transaction(7)]
SQL - Language Statements 2010-05-14 START TRANSACTION(7)