11-14-2012
your volume group is not concurrent capable, not required, but suggested.
are your disks present on all cluster nodes for this resource group?
10 More Discussions You Might Find Interesting
1. AIX
Hello
I am a noobie to HACMP
I have 2 55A servers and a 7031 disk subsystem
For HACMP to work, do I need to have the hdisks on both servers to match the same drives??
The hdisks on each box are currently different:
hdisk0 and hdisk1 are the internal disks and hdisk2-5 are on the D24 on... (1 Reply)
Discussion started by: mhenryj
1 Replies
2. Solaris
I would like to extend a logical drive on our 3510. I have four unallocated disks which I would like to use for this purpose.
The 3510 supports a Sun Cluster but for now all I wish to see is a "new" disk when I run format.
I am a little familiar with the telnet/ssh session on the 3510 but am... (2 Replies)
Discussion started by: malcqv
2 Replies
3. AIX
Hello,
This morning we have added 6 new disks (73 Gb) to our DS4300, then created a new Array en then created a logical drive, after this was done, teh following error occourd on the last 3 (new)disks:
Date/Time: 22-4-08 6:56:26
Sequence number: 5472
Event type: 282D
Event category:... (1 Reply)
Discussion started by: topper
1 Replies
4. HP-UX
Hi,
Can anybody advice whether it is possible to configure HACMP in HP-UX Server.
To my knowledge HACMP is IBM Solution.
Thanks && Regards,
N. Poorna Chandra Rao. (2 Replies)
Discussion started by: npcrao
2 Replies
5. AIX
Hi all,
I have an HACMP (v5.3.0.0) cluster vg attached to ibm shark that need to be decommissioned. The data need to move to the HP EVA disk. The OS is on AIX 5200-10. The plan is to add a new disk from EVA & mirror the existing vg & break the mirror from Shark disk once the mirror finished.
... (12 Replies)
Discussion started by: CW15
12 Replies
6. Shell Programming and Scripting
I need some help with adding lines to file and substitute a pattern.
Ok I have a file:
#cat names.txt
name: John Doe
stationed: 1
name: Michael Sweets
stationed: 41
.
.
.
And would like to change it to:
name: John Doe
employed
permanently
stationed: 1-office (7 Replies)
Discussion started by: hemo21
7 Replies
7. AIX
hi,
when I do a failover, hacmp always starts db2 but recently it fails to start db2..noticed the issue is db2nodes.cfg is not modified by hacmp and is still showing primary node..manually changed the node name to secondary after which db2 started immediately..unable to figure out why hacmp is... (4 Replies)
Discussion started by: gkr747
4 Replies
8. AIX
Hi,
I have a 2 node Cluster. Which is working in active/passive mode (i.e Node#1 is running and when it goes down the Node#2 takes over)
Now there's this requirement that we need a mount point say /test that should be available in active node #1 and when node #1 goes down and node#2 takes... (6 Replies)
Discussion started by: aixromeo
6 Replies
9. AIX
Previous forum threads have noted that AIX cannot use iSCSI disks because it fails when trying to add them to a volume group using mkvg. The failure is caused by AIX's use of the SCSI "WRITE AND VERIFY"(0x2e) command which some iSCSI targets do not support.
We experienced the same problem using... (1 Reply)
Discussion started by: garethr
1 Replies
10. UNIX for Beginners Questions & Answers
I have an array in an external file, "array.txt", which contains:
char *testarray={"Zero", "One", "Two", "Three", "Four", "Five", "Six", "Seven", "Eight", "Nine"};I want to be able to add an element to this array, and have that element display, whenever I call it, without having to recompile... (29 Replies)
Discussion started by: ignatius
29 Replies