Help with adding new disks in HACMP Post: 302731025

10 More Discussions You Might Find Interesting

1. AIX

HACMP (Again)

Hello I am a noobie to HACMP I have 2 55A servers and a 7031 disk subsystem For HACMP to work, do I need to have the hdisks on both servers to match the same drives?? The hdisks on each box are currently different: hdisk0 and hdisk1 are the internal disks and hdisk2-5 are on the D24 on...

2. Solaris

adding existing disks to a 3510 array

I would like to extend a logical drive on our 3510. I have four unallocated disks which I would like to use for this purpose. The 3510 supports a Sun Cluster but for now all I wish to see is a "new" disk when I run format. I am a little familiar with the telnet/ssh session on the 3510 but am...

3. AIX

Critical error after adding 6 new disks in DS4300

Hello, This morning we have added 6 new disks (73 Gb) to our DS4300, then created a new Array en then created a logical drive, after this was done, teh following error occourd on the last 3 (new)disks: Date/Time: 22-4-08 6:56:26 Sequence number: 5472 Event type: 282D Event category:...

4. HP-UX

HACMP in HP-UX

Hi, Can anybody advice whether it is possible to configure HACMP in HP-UX Server. To my knowledge HACMP is IBM Solution. Thanks && Regards, N. Poorna Chandra Rao.

5. AIX

HACMP adding disk for mirroring

Hi all, I have an HACMP (v5.3.0.0) cluster vg attached to ibm shark that need to be decommissioned. The data need to move to the HP EVA disk. The OS is on AIX 5200-10. The plan is to add a new disk from EVA & mirror the existing vg & break the mirror from Shark disk once the mirror finished. ...

6. Shell Programming and Scripting

Adding new lines to a file + adding suffix to a pattern

I need some help with adding lines to file and substitute a pattern. Ok I have a file: #cat names.txt name: John Doe stationed: 1 name: Michael Sweets stationed: 41 . . . And would like to change it to: name: John Doe employed permanently stationed: 1-office

7. AIX

HACMP does not start db2 after failover (db2nodes not getting modified by hacmp)

hi, when I do a failover, hacmp always starts db2 but recently it fails to start db2..noticed the issue is db2nodes.cfg is not modified by hacmp and is still showing primary node..manually changed the node name to secondary after which db2 started immediately..unable to figure out why hacmp is...

8. AIX

Adding a Volume Group to an HACMP Resource Group?

Hi, I have a 2 node Cluster. Which is working in active/passive mode (i.e Node#1 is running and when it goes down the Node#2 takes over) Now there's this requirement that we need a mount point say /test that should be available in active node #1 and when node #1 goes down and node#2 takes...

9. AIX

A solution to the mkvg failure when adding iSCSI disks to AIX.

Previous forum threads have noted that AIX cannot use iSCSI disks because it fails when trying to add them to a volume group using mkvg. The failure is caused by AIX's use of the SCSI "WRITE AND VERIFY"(0x2e) command which some iSCSI targets do not support. We experienced the same problem using...

10. UNIX for Beginners Questions & Answers

Adding to an array in an external file, and adding elements to it.

I have an array in an external file, "array.txt", which contains: char *testarray={"Zero", "One", "Two", "Three", "Four", "Five", "Six", "Seven", "Eight", "Nine"};I want to be able to add an element to this array, and have that element display, whenever I call it, without having to recompile...

LEARN ABOUT CENTOS

mkqdisk

mkqdisk(8)						      Quorum Disk Management							mkqdisk(8)

NAME

       mkqdisk - Cluster Quorum Disk Utility

WARNING

       Use of this command can cause the cluster to malfunction.

SYNOPSIS

       mkqdisk [-?|-h] | [-L] | [-f label] [-c device  -l label] [-d [-d ...]]

DESCRIPTION

       The mkqdisk command is used to create a new quorum disk or display existing quorum disks accessible from a given cluster node.

OPTIONS

       -c device -l label
	      Initialize  a new cluster quorum disk.  This will destroy all data on the given device.  If a cluster is currently using that device
	      as a quorum disk, the entire cluster will malfunction.  Do not run this on an active cluster  when  qdiskd  is  running.	 Only  one
	      device  on  the  SAN should ever have the given label; using multiple different devices is currently not supported (it is expected a
	      RAID array is used for quorum disk redundancy).  The label can be any textual string up to 127 characters - and is therefore  enough
	      space to hold a UUID created with uuidgen(1).

       -f label
	      Find the cluster quorum disk with the given label and display information about it.

       -L     Display information on all accessible cluster quorum disks.

       -d     Increase debugging level.  Specify multiple times for more information.  Currently, specifying more than twice has no effect.

SEE ALSO

       qdisk(5), qdiskd(8), uuidgen(1)

								     July 2006								mkqdisk(8)

10 More Discussions You Might Find Interesting

1. AIX

HACMP (Again)

Discussion started by: mhenryj

2. Solaris

adding existing disks to a 3510 array

Discussion started by: malcqv

3. AIX

Critical error after adding 6 new disks in DS4300

Discussion started by: topper

4. HP-UX

HACMP in HP-UX

Discussion started by: npcrao