Help with adding new disks in HACMP Post: 302731025

10 More Discussions You Might Find Interesting

1. AIX

HACMP (Again)

Hello I am a noobie to HACMP I have 2 55A servers and a 7031 disk subsystem For HACMP to work, do I need to have the hdisks on both servers to match the same drives?? The hdisks on each box are currently different: hdisk0 and hdisk1 are the internal disks and hdisk2-5 are on the D24 on...

2. Solaris

adding existing disks to a 3510 array

I would like to extend a logical drive on our 3510. I have four unallocated disks which I would like to use for this purpose. The 3510 supports a Sun Cluster but for now all I wish to see is a "new" disk when I run format. I am a little familiar with the telnet/ssh session on the 3510 but am...

3. AIX

Critical error after adding 6 new disks in DS4300

Hello, This morning we have added 6 new disks (73 Gb) to our DS4300, then created a new Array en then created a logical drive, after this was done, teh following error occourd on the last 3 (new)disks: Date/Time: 22-4-08 6:56:26 Sequence number: 5472 Event type: 282D Event category:...

4. HP-UX

HACMP in HP-UX

Hi, Can anybody advice whether it is possible to configure HACMP in HP-UX Server. To my knowledge HACMP is IBM Solution. Thanks && Regards, N. Poorna Chandra Rao.

5. AIX

HACMP adding disk for mirroring

Hi all, I have an HACMP (v5.3.0.0) cluster vg attached to ibm shark that need to be decommissioned. The data need to move to the HP EVA disk. The OS is on AIX 5200-10. The plan is to add a new disk from EVA & mirror the existing vg & break the mirror from Shark disk once the mirror finished. ...

6. Shell Programming and Scripting

Adding new lines to a file + adding suffix to a pattern

I need some help with adding lines to file and substitute a pattern. Ok I have a file: #cat names.txt name: John Doe stationed: 1 name: Michael Sweets stationed: 41 . . . And would like to change it to: name: John Doe employed permanently stationed: 1-office

7. AIX

HACMP does not start db2 after failover (db2nodes not getting modified by hacmp)

hi, when I do a failover, hacmp always starts db2 but recently it fails to start db2..noticed the issue is db2nodes.cfg is not modified by hacmp and is still showing primary node..manually changed the node name to secondary after which db2 started immediately..unable to figure out why hacmp is...

8. AIX

Adding a Volume Group to an HACMP Resource Group?

Hi, I have a 2 node Cluster. Which is working in active/passive mode (i.e Node#1 is running and when it goes down the Node#2 takes over) Now there's this requirement that we need a mount point say /test that should be available in active node #1 and when node #1 goes down and node#2 takes...

9. AIX

A solution to the mkvg failure when adding iSCSI disks to AIX.

Previous forum threads have noted that AIX cannot use iSCSI disks because it fails when trying to add them to a volume group using mkvg. The failure is caused by AIX's use of the SCSI "WRITE AND VERIFY"(0x2e) command which some iSCSI targets do not support. We experienced the same problem using...

10. UNIX for Beginners Questions & Answers

Adding to an array in an external file, and adding elements to it.

I have an array in an external file, "array.txt", which contains: char *testarray={"Zero", "One", "Two", "Three", "Four", "Five", "Six", "Seven", "Eight", "Nine"};I want to be able to add an element to this array, and have that element display, whenever I call it, without having to recompile...

LEARN ABOUT NETBSD

vgreduce

VGREDUCE(8)						      System Manager's Manual						       VGREDUCE(8)

NAME

       vgreduce - reduce a volume group

SYNOPSIS

       vgreduce  [-a|--all] [-A|--autobackup y|n] [-d|--debug] [-h|-?|--help] [--removemissing] [-t|--test] [-v|--verbose] VolumeGroupName [Physi-
       calVolumePath...]

DESCRIPTION

       vgreduce allows you to remove one or more unused physical volumes from a volume group.

OPTIONS

       See lvm for common options.

       -a, --all
	      Removes all empty physical volumes if none are given on command line.

       --removemissing
	      Removes all missing physical volumes from the volume group, if there are no logical volumes allocated on those. This resumes  normal
	      operation of the volume group (new logical volumes may again be created, changed and so on).

	      If this is not possible (there are logical volumes referencing the missing physical volumes) and you cannot or do not want to remove
	      them manually, you can run this option with --force to have vgreduce remove any partial LVs.

	      Any logical volumes and dependent snapshots that were partly on the missing disks get removed completely. This includes those  parts
	      that lie on disks that are still present.

	      If your logical volumes spanned several disks including the ones that are lost, you might want to try to salvage data first by acti-
	      vating your logical volumes with --partial as described in lvm (8).

SEE ALSO

       lvm(8), vgextend(8)

Sistina Software UK					 LVM TOOLS 2.02.44-cvs (02-17-09)					       VGREDUCE(8)

10 More Discussions You Might Find Interesting

1. AIX

HACMP (Again)

Discussion started by: mhenryj

2. Solaris

adding existing disks to a 3510 array

Discussion started by: malcqv

3. AIX

Critical error after adding 6 new disks in DS4300

Discussion started by: topper

4. HP-UX

HACMP in HP-UX

Discussion started by: npcrao