esbsit03# lsvg sirg3vg1
VOLUME GROUP: sirg3vg1 VG IDENTIFIER: 00084dd00000d70000000118cb70623f
VG STATE: active PP SIZE: 32 megabyte(s)
VG PERMISSION: read/write TOTAL PPs: 4474 (143168 megabytes)
MAX LVs: 256 FREE PPs: 56 (1792 megabytes)
LVs: 3 USED PPs: 4418 (141376 megabytes)
OPEN LVs: 3 QUORUM: 4 (Enabled)
TOTAL PVs: 6 VG DESCRIPTORS: 6
STALE PVs: 0 STALE PPs: 0
ACTIVE PVs: 6 AUTO ON: no
MAX PPs per VG: 32512
MAX PPs per PV: 1016 MAX PVs: 32
LTG size (Dynamic): 256 kilobyte(s) AUTO SYNC: no
HOT SPARE: no BB POLICY: relocatable
Hello
I am a noobie to HACMP
I have 2 55A servers and a 7031 disk subsystem
For HACMP to work, do I need to have the hdisks on both servers to match the same drives??
The hdisks on each box are currently different:
hdisk0 and hdisk1 are the internal disks and hdisk2-5 are on the D24 on... (1 Reply)
I would like to extend a logical drive on our 3510. I have four unallocated disks which I would like to use for this purpose.
The 3510 supports a Sun Cluster but for now all I wish to see is a "new" disk when I run format.
I am a little familiar with the telnet/ssh session on the 3510 but am... (2 Replies)
Hello,
This morning we have added 6 new disks (73 Gb) to our DS4300, then created a new Array en then created a logical drive, after this was done, teh following error occourd on the last 3 (new)disks:
Date/Time: 22-4-08 6:56:26
Sequence number: 5472
Event type: 282D
Event category:... (1 Reply)
Hi,
Can anybody advice whether it is possible to configure HACMP in HP-UX Server.
To my knowledge HACMP is IBM Solution.
Thanks && Regards,
N. Poorna Chandra Rao. (2 Replies)
Hi all,
I have an HACMP (v5.3.0.0) cluster vg attached to ibm shark that need to be decommissioned. The data need to move to the HP EVA disk. The OS is on AIX 5200-10. The plan is to add a new disk from EVA & mirror the existing vg & break the mirror from Shark disk once the mirror finished.
... (12 Replies)
I need some help with adding lines to file and substitute a pattern.
Ok I have a file:
#cat names.txt
name: John Doe
stationed: 1
name: Michael Sweets
stationed: 41
.
.
.
And would like to change it to:
name: John Doe
employed
permanently
stationed: 1-office (7 Replies)
hi,
when I do a failover, hacmp always starts db2 but recently it fails to start db2..noticed the issue is db2nodes.cfg is not modified by hacmp and is still showing primary node..manually changed the node name to secondary after which db2 started immediately..unable to figure out why hacmp is... (4 Replies)
Hi,
I have a 2 node Cluster. Which is working in active/passive mode (i.e Node#1 is running and when it goes down the Node#2 takes over)
Now there's this requirement that we need a mount point say /test that should be available in active node #1 and when node #1 goes down and node#2 takes... (6 Replies)
Previous forum threads have noted that AIX cannot use iSCSI disks because it fails when trying to add them to a volume group using mkvg. The failure is caused by AIX's use of the SCSI "WRITE AND VERIFY"(0x2e) command which some iSCSI targets do not support.
We experienced the same problem using... (1 Reply)
I have an array in an external file, "array.txt", which contains:
char *testarray={"Zero", "One", "Two", "Three", "Four", "Five", "Six", "Seven", "Eight", "Nine"};I want to be able to add an element to this array, and have that element display, whenever I call it, without having to recompile... (29 Replies)
Discussion started by: ignatius
29 Replies
LEARN ABOUT LINUX
clinfo
clinfo(1M) System Administration Commands clinfo(1M)NAME
clinfo - display cluster information
SYNOPSIS
clinfo [-nh]
DESCRIPTION
The clinfo command displays cluster configuration information about the node from which the command is executed.
Without arguments, clinfo returns an exit status of 0 if the node is configured and booted as part of a cluster. Otherwise, clinfo returns
an exit status of 1.
OPTIONS
The following options are supported:
-h Displays the highest node number allowed to be configured. This is different from the maximum number of nodes supported in a given
cluster. The current highest configured node number can change immediately after the command returns since new nodes can be dynam-
ically added to a running cluster.
For example, clinfo -h might return 64, meaning that the highest number you can use to identify a node is 64. See the Sun Cluster
3.0 System Administration Guide for a description of utilities you can use to determine the number of nodes in a cluster.
-n Prints the number of the node from which clinfo is executed.
EXIT STATUS
The following exit values are returned:
0 Successful completion.
1 An error occurred.
This is usually because the node is not configured or booted as part of a cluster.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO attributes(5)SunOS 5.10 12 Mar 2002 clinfo(1M)