Help with adding new disks in HACMP Post: 302730997

Sponsored Content

Operating Systems AIX Help with adding new disks in HACMP Post 302730997 by newtoaixos on Wednesday 14th of November 2012 03:52:48 AM

11-14-2012

Registered User

Help with adding new disks in HACMP

Hi.

Below is the output requested :

Code:

esbsit03# lsvg sirg3vg1
VOLUME GROUP:       sirg3vg1                 VG IDENTIFIER:  00084dd00000d70000000118cb70623f
VG STATE:           active                   PP SIZE:        32 megabyte(s)
VG PERMISSION:      read/write               TOTAL PPs:      4474 (143168 megabytes)
MAX LVs:            256                      FREE PPs:       56 (1792 megabytes)
LVs:                3                        USED PPs:       4418 (141376 megabytes)
OPEN LVs:           3                        QUORUM:         4 (Enabled)
TOTAL PVs:          6                        VG DESCRIPTORS: 6
STALE PVs:          0                        STALE PPs:      0
ACTIVE PVs:         6                        AUTO ON:        no
MAX PPs per VG:     32512
MAX PPs per PV:     1016                     MAX PVs:        32
LTG size (Dynamic): 256 kilobyte(s)          AUTO SYNC:      no
HOT SPARE:          no                       BB POLICY:      relocatable

newtoaixos

View Public Profile for newtoaixos

Find all posts by newtoaixos

10 More Discussions You Might Find Interesting

1. AIX

HACMP (Again)

Hello I am a noobie to HACMP I have 2 55A servers and a 7031 disk subsystem For HACMP to work, do I need to have the hdisks on both servers to match the same drives?? The hdisks on each box are currently different: hdisk0 and hdisk1 are the internal disks and hdisk2-5 are on the D24 on...

2. Solaris

adding existing disks to a 3510 array

I would like to extend a logical drive on our 3510. I have four unallocated disks which I would like to use for this purpose. The 3510 supports a Sun Cluster but for now all I wish to see is a "new" disk when I run format. I am a little familiar with the telnet/ssh session on the 3510 but am...

3. AIX

Critical error after adding 6 new disks in DS4300

Hello, This morning we have added 6 new disks (73 Gb) to our DS4300, then created a new Array en then created a logical drive, after this was done, teh following error occourd on the last 3 (new)disks: Date/Time: 22-4-08 6:56:26 Sequence number: 5472 Event type: 282D Event category:...

4. HP-UX

HACMP in HP-UX

Hi, Can anybody advice whether it is possible to configure HACMP in HP-UX Server. To my knowledge HACMP is IBM Solution. Thanks && Regards, N. Poorna Chandra Rao.

5. AIX

HACMP adding disk for mirroring

Hi all, I have an HACMP (v5.3.0.0) cluster vg attached to ibm shark that need to be decommissioned. The data need to move to the HP EVA disk. The OS is on AIX 5200-10. The plan is to add a new disk from EVA & mirror the existing vg & break the mirror from Shark disk once the mirror finished. ...

6. Shell Programming and Scripting

Adding new lines to a file + adding suffix to a pattern

I need some help with adding lines to file and substitute a pattern. Ok I have a file: #cat names.txt name: John Doe stationed: 1 name: Michael Sweets stationed: 41 . . . And would like to change it to: name: John Doe employed permanently stationed: 1-office

7. AIX

HACMP does not start db2 after failover (db2nodes not getting modified by hacmp)

hi, when I do a failover, hacmp always starts db2 but recently it fails to start db2..noticed the issue is db2nodes.cfg is not modified by hacmp and is still showing primary node..manually changed the node name to secondary after which db2 started immediately..unable to figure out why hacmp is...

8. AIX

Adding a Volume Group to an HACMP Resource Group?

Hi, I have a 2 node Cluster. Which is working in active/passive mode (i.e Node#1 is running and when it goes down the Node#2 takes over) Now there's this requirement that we need a mount point say /test that should be available in active node #1 and when node #1 goes down and node#2 takes...

9. AIX

A solution to the mkvg failure when adding iSCSI disks to AIX.

Previous forum threads have noted that AIX cannot use iSCSI disks because it fails when trying to add them to a volume group using mkvg. The failure is caused by AIX's use of the SCSI "WRITE AND VERIFY"(0x2e) command which some iSCSI targets do not support. We experienced the same problem using...

10. UNIX for Beginners Questions & Answers

Adding to an array in an external file, and adding elements to it.

I have an array in an external file, "array.txt", which contains: char *testarray={"Zero", "One", "Two", "Three", "Four", "Five", "Six", "Seven", "Eight", "Nine"};I want to be able to add an element to this array, and have that element display, whenever I call it, without having to recompile...

LEARN ABOUT DEBIAN

4s-backend-setup

4S-BACKEND_SETUP(1J)						      4store						      4S-BACKEND_SETUP(1J)

NAME

     4s-backend-setup -- Create a new 4store KB

SYNOPSIS

     4s-backend-setup kbname [--node node-number] [--cluster cluster-size] [--segments segment-count] kb-name

		      --node  Number of this node in the cluster, values range from 0 to cluster-size - 1.  The default is 0.

		      --cluster
			      The number of nodes in the cluster.  The default is 1.

		      --segments
			      The number of segments in the cluster. The default is 2. We recommend one for each CPU core in the cluster as a good
			      starting point. Higher numbers tend to consume more resources, but may result in increased performance.

NOTES

     Once crated with 4s-backend-setup KBs should be started with 4s-backend(1)

SEE ALSO

     4s-query(1), 4s-size(1), 4s-httpd(1), 4s-backend(1), 4s-delete-model(1)

EXAMPLES

     $ 4s-backend-setup --node 0 --cluster 1 --segments 4 demo

     Creates the indexes for a single-machine KB with four segments, named "demo".

4store								   May 31, 2019 							    4store

10 More Discussions You Might Find Interesting

1. AIX

HACMP (Again)

Discussion started by: mhenryj

2. Solaris

adding existing disks to a 3510 array

Discussion started by: malcqv

3. AIX

Critical error after adding 6 new disks in DS4300

Discussion started by: topper

4. HP-UX

HACMP in HP-UX

Discussion started by: npcrao