parunlock(1M)															     parunlock(1M)

NAME

       parunlock - unlock stable complex profile or cancel pending changes to complex or partition configuration data

SYNOPSIS

       cell]
	      username

       cell] PartitionNumber]
	      username

       cell] PartitionNumber]
	      username

       PartitionNumber]
	      username

       cell] PartitionNumber]
	      username

	      username

DESCRIPTION

       The  command  unlocks  the specified Partition Configuration Data, the Dynamic Complex Configuration Data, the Stable Complex Configuration
       Data, or the cell data; or cancels pending changes to the Stable Complex Configuration Data; or any combination of these.

       This command should be used with caution.  It should be used only when the system resources are locked due to the abnormal  termination	of
       any partition command or other similar applications.

       Superuser  permission  is  required to run this command on the local partition.	If the option is used to access a remote partition or com-
       plex, superuser permission is not required on the local system, and the local system need not exist on an nPartition.   If  the	option	is
       specified, username on the remote host must have superuser permission or the command will fail.

       Refer to the for a description of the partition management terms used in this man page.

   Options and Arguments
       recognizes the following command line options and arguments:
       Unlocks	the  Partition	Configuration  Data of the specified target partition on the target complex.  PartitionNumber specifies the unique
       number (integer) assigned to the partition when it was created.

       Unlocks the Stable Complex Configuration Data, the Dynamic Complex
	      Configuration Data, the Partition Configuration Data of all the partitions on the target complex and the cell data of all the  cells
	      in the target complex.

       Unlocks the cell data of the specified cell.  A
	      cell  can  be  specified either in the local (cabinet#/slot#) or global (cell#) format.  For example, the cell located in cabinet 0,
	      slot 1 is identified in the local format as 0/1 or in the global format as 1.

       Unlocks the Dynamic Complex Configuration Data of the target complex.

       Allows access to the complex specified by the
	      option.  The accessed complex is then considered the target complex.  Access is through the service processor's LAN port.

	      The option is required if this option is used.

	      If this option is specified, the command prompts for the password.

	      If an error is reported when you attempt to connect using this option, check to see that IPMI LAN access has not	been  disabled	on
	      the  remote  service processor.  Access to the complex through IPMI over LAN can be enabled or disabled by logging on to the service
	      processor and using the command from the Command Menu.

	      The and options are mutually exclusive.

       This option should only be used in combination with either the
	      or option.  IPaddress|hostname specifies the IP address or hostname of the target partition or complex

       Cancels any pending changes to the Stable Complex Configuration Data of
	      the target complex.

       Unlocks the Stable Complex Configuration Data of the target complex.

       Specifies the required authorization to access a partition other than
	      the local partition (but can also be used as a loopback access to the local partition).  The complex to be modified is  the  one	in
	      which this target partition resides.

	      The option is required if this option is used.

	      If this option is specified, the command prompts for the password.

	      username specifies a configured user name on the target partition.

	      Note: This command is a Web-Based Enterprise Management (WBEM) Client Application.  The option accesses the target partition using a
	      Secure Sockets Layer (SSL) connection.  If errors are reported, check that the conditions described in the section are satisfied.

   Mapping of Global Cell Numbers to Local Cell Numbers
       The cabinets in a complex are numbered starting from 0.	The cell slots in each cabinet are also numbered starting from	0.   Each  cabinet
       can have a maximum of 8 cells.  For example, the cells located in cabinet 0 will have the following cell numbers in global format: 0, 1, 2,
       3, 4, 5, 6, 7.  The cell numbers in corresponding local format will be 0/0, 0/1, 0/2, 0/3, 0/4, 0/5, 0/6, 0/7.

       Similarly the cells located in cabinet 1 will have the following cell numbers in global format: 8, 9, 10, 11, 12, 13,  14,  15.	 The  cell
       numbers in corresponding local format will be 1/0, 1/1, 1/2, 1/3, 1/4, 1/5, 1/6, 1/7.

       From the above convention the cell located in cabinet 1, slot 0 is identified in the local format as 1/0 or in the global format as 8.  The
       command will display the above cell as "cab1,cell0".  The cell located in cabinet 1, slot 4 is identified in the local format as 1/4 or	in
       the global format as 12.  The command will display the above cell as "cab1,cell4".  See parstatus(1).

RETURN VALUE

       The command exits with one of the following values:

       Successful completion.
       Error condition occurred.

EXAMPLES

       Unlock the Partition Configuration Data of the partition whose partition number is

       Unlock the cell data of the cell

       Unlock the Stable Complex Configuration Data on the local complex.

       Unlock the Dynamic Complex Configuration Data on the local complex.

       Unlock  the  Stable  Complex Configuration Data, the Dynamic Complex Configuration Data, the Partition Configuration Data of all the parti-
       tions on the local complex and the cell data of all the cells in the local complex.

DEPENDENCIES

       This command uses the Web-Based Enterprise Management (WBEM) product and some of its configuration settings.  If you  encounter	connection
       errors when using the option, check that the following two conditions are satisfied:

       o  Use  the command (see cimconfig(1M) in the WBEM product documentation) to verify (and correct if necessary) the setting of the following
	  two variables:

	  o

	  o

       o  The target partition's digital certificate has been appended to the local partition's Shared Authentication Store.  For  the	nPartition
	  commands, the Shared Authentication Store is stored in the file: This file is used by all the clients, which use SSL based certificates.
	  If these clients trust a target partition, then the nPartition commands will also trust the target partition.

       Refer to the WBEM documents specified in the section below for further information.

AUTHOR

       was developed by the Hewlett-Packard Company.

SEE ALSO

       fruled(1),  parstatus(1),  cplxmodify(1M),  frupower(1M),  parconfig(1M),  parcreate(1M),  parmgr(1M),  parmodify(1M),  parolrad(1M),  par-
       remove(1M), partition(5).

       on

       on

       on

																     parunlock(1M)