filter out the corresponding columns from the output of "ls -l". Transform the separators to single blanks, then use "cut -d..." to get certain columns (replace "<spc>" with literal space characters):
Hello all,
I have a directory filling up. I need to determine the size of the files in the directory. How do I do that, what command should I run when I am in the directory?
Next question, can I expand the partition size? (10 Replies)
I'm new to HP-UX and am looking for the command that will allow to me determine the total size of listed files. I'm being told that my backup selection is exceeding my tape drive size and need to determine how much information is being backed up.
Help? (3 Replies)
Hello!
I'm trying to find out the total file size of a subset list in a directory. For example, I do not need to know the total file size of all the files in a directory, but I need to know what the total size is of say, "ls -l *FEB08*" in a directory. Is there any easy way of doing this?
... (3 Replies)
HI,
Can any tell me how to filter the list of files greater than the size specified by user. The size should be provided by user as an input.
Regards
shiva (6 Replies)
If I have a file x.txt that is 8 bytes... I want to enter
>> x.txt
8
I've played around with ls, and du... and they always list the file name. (2 Replies)
Hi,
I have directories with name like:
aaa
bbb
ccc
...
I would like to to see which directories are the largest and then list the files within each. I have success using:
du -ks * | sort -rin | head -n 20
which gives me an output like:
120 bbb
27 ccc
3 aaa
...
I would like... (3 Replies)
i have a files in the dir as below.
ls -lR ./.snapshot
5649600512 ./.snapshot/backup/data20080707
6006923264 ./.snapshot/backup/data20080708
5321129984 ./.snapshot/backup/data20080709
6686597120 ./.snapshot/backup/data20080710
7312855040 ... (4 Replies)
Hello,
I have a flat file with a list of files with the path to the file and I am attempting to calculate the filesize for each one; however xargs isn't playing nicely and I am sure there is probably a better way of doing this.
What I envisioned is this:
cat filename|xargs -i ls -l {} |awk... (4 Replies)
how to get the file name list with size descriptive in hp-ux
Required output:
permission link user group size(with MB,KB,GB etc) date time name (7 Replies)
I used to use ls -l cut to detrmine file size, and google searches didn't come up with anything else but 'stat' which doesn't appear on HPUX.
I discovered the humble 'wc -c' which does this job very neatly, and thought I would share it. (7 Replies)
Discussion started by: tbochan
7 Replies
LEARN ABOUT NETBSD
cut
CUT(1) BSD General Commands Manual CUT(1)NAME
cut -- select portions of each line of a file
SYNOPSIS
cut -b list [-n] [file ...]
cut -c list [file ...]
cut -f list [-d delim] [-s] [file ...]
DESCRIPTION
The cut utility selects portions of each line (as specified by list) from each file and writes them to the standard output. If the file
argument is a single dash ('-') or no file arguments were specified, lines are read from the standard input. The items specified by list can
be in terms of column position or in terms of fields delimited by a special character. Column numbering starts from 1.
list is a comma or whitespace separated set of increasing numbers and/or number ranges. Number ranges consist of a number, a dash (-), and a
second number and select the fields or columns from the first number to the second, inclusive. Numbers or number ranges may be preceded by a
dash, which selects all fields or columns from 1 to the first number. Numbers or number ranges may be followed by a dash, which selects all
fields or columns from the last number to the end of the line. Numbers and number ranges may be repeated, overlapping, and in any order. It
is not an error to select fields or columns not present in the input line.
The options are as follows:
-b list The list specifies byte positions.
-c list The list specifies character positions.
-d string Use the first character of string as the field delimiter character. The default is the <TAB> character.
-f list The list specifies fields, separated by the field delimiter character. The selected fields are output, separated by the field
delimiter character.
-n Do not split multi-byte characters.
-s Suppresses lines with no field delimiter characters. Unless specified, lines with no delimiters are passed through unmodified.
EXIT STATUS
cut exits 0 on success, 1 if an error occurred.
SEE ALSO paste(1)STANDARDS
The cut utility conforms to IEEE Std 1003.2-1992 (``POSIX.2'').
BSD December 21, 2008 BSD