filter out the corresponding columns from the output of "ls -l". Transform the separators to single blanks, then use "cut -d..." to get certain columns (replace "<spc>" with literal space characters):
Code:
ls -l | sed 's/<spc><spc>*/<spc>/g' | cut -d '<spc>' -f5,9
Hello all,
I have a directory filling up. I need to determine the size of the files in the directory. How do I do that, what command should I run when I am in the directory?
Next question, can I expand the partition size? (10 Replies)
I'm new to HP-UX and am looking for the command that will allow to me determine the total size of listed files. I'm being told that my backup selection is exceeding my tape drive size and need to determine how much information is being backed up.
Help? (3 Replies)
Hello!
I'm trying to find out the total file size of a subset list in a directory. For example, I do not need to know the total file size of all the files in a directory, but I need to know what the total size is of say, "ls -l *FEB08*" in a directory. Is there any easy way of doing this?
... (3 Replies)
HI,
Can any tell me how to filter the list of files greater than the size specified by user. The size should be provided by user as an input.
Regards
shiva (6 Replies)
If I have a file x.txt that is 8 bytes... I want to enter
>> x.txt
8
I've played around with ls, and du... and they always list the file name. (2 Replies)
Hi,
I have directories with name like:
aaa
bbb
ccc
...
I would like to to see which directories are the largest and then list the files within each. I have success using:
du -ks * | sort -rin | head -n 20
which gives me an output like:
120 bbb
27 ccc
3 aaa
...
I would like... (3 Replies)
i have a files in the dir as below.
ls -lR ./.snapshot
5649600512 ./.snapshot/backup/data20080707
6006923264 ./.snapshot/backup/data20080708
5321129984 ./.snapshot/backup/data20080709
6686597120 ./.snapshot/backup/data20080710
7312855040 ... (4 Replies)
Hello,
I have a flat file with a list of files with the path to the file and I am attempting to calculate the filesize for each one; however xargs isn't playing nicely and I am sure there is probably a better way of doing this.
What I envisioned is this:
cat filename|xargs -i ls -l {} |awk... (4 Replies)
how to get the file name list with size descriptive in hp-ux
Required output:
permission link user group size(with MB,KB,GB etc) date time name (7 Replies)
I used to use ls -l cut to detrmine file size, and google searches didn't come up with anything else but 'stat' which doesn't appear on HPUX.
I discovered the humble 'wc -c' which does this job very neatly, and thought I would share it. (7 Replies)
Discussion started by: tbochan
7 Replies
LEARN ABOUT OPENDARWIN
cut
CUT(1) BSD General Commands Manual CUT(1)NAME
cut -- select portions of each line of a file
SYNOPSIS
cut -b list [-n] [file ...]
cut -c list [file ...]
cut -f list [-d delim] [-s] [file ...]
DESCRIPTION
The cut utility selects portions of each line (as specified by list) from each file and writes them to the standard output. If no file argu-
ments are specified, or a file argument is a single dash ('-'), cut reads from from the standard input. The items specified by list can be
in terms of column position or in terms of fields delimited by a special character. Column numbering starts from 1.
The list option argument is a comma or whitespace separated set of increasing numbers and/or number ranges. Number ranges consist of a num-
ber, a dash ('-'), and a second number and select the fields or columns from the first number to the second, inclusive. Numbers or number
ranges may be preceded by a dash, which selects all fields or columns from 1 to the first number. Numbers or number ranges may be followed
by a dash, which selects all fields or columns from the last number to the end of the line. Numbers and number ranges may be repeated, over-
lapping, and in any order. It is not an error to select fields or columns not present in the input line.
The options are as follows:
-b list
The list specifies byte positions.
-c list
The list specifies character positions.
-d delim
Use the first character of delim as the field delimiter character instead of the tab character.
-f list
The list specifies fields, delimited in the input by a single tab character. Output fields are separated by a single tab character.
-n Do not split multi-byte characters.
-s Suppress lines with no field delimiter characters. Unless specified, lines with no delimiters are passed through unmodified.
ENVIRONMENT
The LANG, LC_ALL and LC_CTYPE environment variables affect the execution of cut if the -n option is specified. Their effect is described in
environ(7).
EXAMPLES
Extract users' login names and shells from the system passwd(5) file as ``name:shell'' pairs:
cut -d : -f 1,7 /etc/passwd
Show the names and login times of the currently logged in users:
who | cut -c 1-16,26-38
DIAGNOSTICS
The cut utility exits 0 on success, and >0 if an error occurs.
SEE ALSO paste(1)STANDARDS
The cut utility conforms to IEEE Std 1003.2-1992 (``POSIX.2'').
HISTORY
A cut command appeared in AT&T System III UNIX.
BUGS
The -c option is a synonym for the -b option, which causes incorrect behaviour in locales that support multibyte characters.
When operating on fields (-f option is specified), cut does not recognise multibyte characters, and the delim character is recognised in the
middle of multibyte sequences.
BSD June 6, 1993 BSD