I have Sun Ultra 5/10 UltraSPARC-IIi 440 Mhz ) OpenBoot 3.19 with 1024 MB and IDE disk
I have the following error shown in the attached photos and video kindly advise
Hi,
I am planning to purchase a sun ultra 10 or 30, i was wondering what is the difference between them. I tried looking up for sun documentation and cannot find any info. Please help me. Thanks
Soul (1 Reply)
Not necessarily a Solaris question, but thought this the best place for it.
My main Linux/OpenBSD workstation (really old athlon) is on its way out, and I am considering getting an Ultra 30 or 60 to replace it with. If I go with a dual proc 60 I'll get SMP support on Linux. Most systems I've... (1 Reply)
I need to move everything from an older ultra 1 onto a newer ultra 60 (OS and all) running SUNOS 5.5.1. Any suggestions on the best way to do this?
Frank
P.S. If you know of a document somewhere please let me know. (11 Replies)
Hi,
I would like to upgrade the memory to 8GB and two more cpu's is it possbile to upgrade?
Currently I have...
# uname -a
SunOS bdsn4003 5.8 Generic_117350-33 sun4u sparc SUNW,Ultra-60
# prtconf
System Configuration: Sun Microsystems sun4u
Memory size: 2048 Megabytes
System... (1 Reply)
Has anyone successfully tried installing Solaris 10 on an Ultra 4??
The machine in question has a 300MHz SPARCIIi CPU and 1 GB of RAM which - according to the SUN doco should be enough. However when I try and install it just hangs on the "configuring Devices" message. I left it overnight to see... (2 Replies)
Dear All,
I Have problem at my console Ultra 24 Intel. OS : solaris 10 with kernel 13xxxx. Error message is :
May 11 13:27:08 unknown agent: syslog
May 11 13:27:08 agent agentServer parameter (xxxxx) is not a valid local hostname
May 11 13:27:08 unknown agent: syslog
May... (8 Replies)
Hi all,
I must install 2.6 and 2.5.1 on ultra 80's. I need Operating Environment Installation CD p/n 704-6914-10 (Sept 99) or
704-7076-10 (Feb 2000)and also the manual "Installing Solaris 2.5.1 or Solaris 2.6 Software on 419+ MHz Systems"
will be really helpfull.
I can not reach that CD... (0 Replies)
I have a nice Ultra 10 (440 MHz, 1 GB RAM, 40 GB Disk, Elite3D m6 Graphics), which probably needs a new install. Currently it is running Solaris 10 with Java Desktop. Imho Java Desktop slows the computer a little bit down. Since a few days a have also a SunPCi II card.
Now I want to reinstall... (3 Replies)
Hi,
as being discussed in this Thread some time ago, I need the "Solaris Operating Environment Installation CD" to be able to install Solaris releases before 7 on my lovely U80. Part number is 704-7076-10.
Does anyone still have this hanging around?
Regards,
Oli
... (5 Replies)
Discussion started by: oreissig
5 Replies
LEARN ABOUT OSF1
atapi_ide
atapi_ide(7) Miscellaneous Information Manual atapi_ide(7)NAME
atapi_ide - Interface for ATAPI or IDE (PC) devices
SYNOPSIS
PCI bus CMD/Acer ATAPI/IDE adapter:
bus pci0 at *
bus ata0 at *
controller scsi0 at ata0 slot 0
controller scsi1 at ata0 slot 1
PCI bus Cypress ATAPI/IDE adapter:
bus pci0 at *
bus ata0 at *
bus ata1 at *
controller scsi0 at ata0 slot 0
controller scsi1 at ata1 slot 0
PCMCIA bus ATA/IDE disk card:
bus pcmcia0 at *
bus ata0 at pcmcia?
controller scsi0 at ata0
DESCRIPTION
Devices commonly known for their use on PC devices as ATA or IDE devices are supported using the SCSI CAM device driver. The ATA standard
has also been expanded to include what are known as ATAPI devices. The SCSI CAM device driver is also used for those disks and CD-ROM
devices. These devices may also be known under the names EIDE, ATA-2, Fast-ATA, or Ultra-ATA.
Beacuse the ATA/IDE standard was not developed until after many of the devices that used this standard were produced, there are many
devices which do not strictly comply with the standard. While it is possible some industry standard devices may appear to work, it is also
possible they will cause hang or data corruption cases when used under more stressful situations. For this reason, it is recommended that
only the supported devices be used. These devices have been tested and are certified for correct operation.
ATAPI/IDE controllers allow the connection of two devices. These two devices are known as the master device and the slave device. If only
one device is connected, that device must be the master (slave-only configurations are not supported). When used by the SCSI CAM device
driver, the IDE master device is assigned SCSI id 0 for that controller. The slave device is assigned SCSI id 1 for that controller. No
other SCSI ids are assigned on that controller. Most ATAPI/IDE adapters contain two channels (known as the primary and secondary). Each
of these channels may contain their own master and slave devices. Therefore, a dual channel ATAPI/IDE controller may contain up to 4
devices (a master and slave pair on each channel). These 4 devices are then accessed as SCSI id 0 and 1 on each channel.
Many SCSI operations translate perfectly for use on IDE. For example, read and write operations are the same. However, many SCSI disk
mode pages are emulated by the IDE device driver. For example, you can display the SCSI inquiry mode pages using the following command: %
scu show inq pages pages are created by the device driver to contain the long (full IDE) form of the device name, serial number, revision,
and the operational modes of the device. Only a shortened version of this information is available with the standard SCSI inquiry command.
Note also that the following command: % scu show pages Shows that the SCSI mode pages contain only partial information. Only that informa-
tion (such as geometry) that the drive reports to the system is able to be reformatted into these emulated SCSI mode pages. Much of the
information (such as RPM) is simply not available from the drive, and therefore not accurately reported.
ATAPI devices are much more closely related to SCSI devices, and as such contain their own mode pages. Therefore, for these devices, the
mode page values reported are those from the device, and no emulation is involved.
ATAPI tape devices are not supported at this time.
FILES
/dev/disk/dsk??? /dev/disk/dsk???
RELATED INFORMATION SCSI(7), rz(7), and disklabel(8) delim off
atapi_ide(7)