I see your script is checking if the process is running, using logger to log the status and terminating. This is the reason why you are not seeing it running. You should put this in an infinite while loop with a sleep time of your choice for periodically checking and logging the status.
E.g:-
Now you can start your script using nohup and open another terminal to check if it is running:-
I want to write a unix shell script that will check if a process (say debu) is running in the server or not. If no , then send a mail to the corresponding person to start the process??? (2 Replies)
Hi,
I am a unix newbie. I need to write a script to check wheteher another script is still running. If it is, then sleep for 30m and then check again if the script is running. If the script has stopped running then, I need to come out of the loop.
I am using RHEL 5.2 (2 Replies)
Hi guys,
I'm new to scripting and I'm wondering if I can run a matlab script from within a bash script.
Basically, at the minute I have a bash script which creates a file "bottfile.xyz"
I then import "bottfile.xyz" into matlab using importdata('bottfile.xyz'). Then I just run the matlab... (0 Replies)
Hey guys, so I wrote a small script that pretty much just takes in two numbers and counts from the first to the second, e.g.
unknown-hacker|544> count.sh 1 3
1
2
3
My problem is I want to make it so that if you input invalid parameters, such as non-numerical characters, more than 2... (2 Replies)
I'm a bit new to bash programming and I was assigned the job of writing a script that will check to see if a program server is running and to restart the program if it is not up. The script is supposed to check the program every hour (which I have looked up and I believe I know how to do) and send... (3 Replies)
Hi,
I want to write a script which continuously checking status of a script running in background by nohup command. And if same script is not running then immediately start the script...please help..
i am using below command to run script
nohup system_traps.sh &
but in some... (9 Replies)
I have one shell script in NAS shared location. Since NAS is mounted in many servers, script can be run from any of those servers.
I want to make sure if the script is already running, it should not allow others to run it. I googled it and got some idea that i can touch one empty file in the... (8 Replies)
How to check the day name,is it saturday in bash shell script.
If dayname = saturday then
run the full load
else
run just the incremental loads
end if
Thank you very much for the helpful information. (4 Replies)
I am working on script. it reads a file which contains multiple lines
Ex;
curl --write-out %{http_code} --silent --output /dev/null http://hostname:port/input=1
curl --write-out %{http_code} --silent --output /dev/null http://hostname:port/input=2
curl --write-out %{http_code} --silent ... (2 Replies)
Discussion started by: oraclermanpt
2 Replies
LEARN ABOUT LINUX
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)