I asked a similar question earlier and got a very good answer but a new doubt came up. This is a few lines of a '/sbin/ifconfig' command on my PC:
RX packets:3781025 errors:0 dropped:0 overruns:0 frame:0
TX packets:1941909 errors:0 dropped:0 overruns:0 carrier:0
Does the RX and TX packets... (1 Reply)
I'm trying to install the recommended patch cluster on a x86 Solaris 10 box.
I get this error:
ERROR: /sbin/zonename cannot be found. install_cluster for 10_x86 patch cluster not applied. Exiting.
I tried touching the file and it gave a different error of: expected argument..
anyone... (1 Reply)
I am executing a stored proc and sending the results in a log file. I then want to grab one result from the output parameters (bolded below, 2) so that I can store it in a variable which will then be called in another script. There are more details that get printed in the beginning of the log file,... (3 Replies)
Hi -
Trying to understand a few things from an ifconfig -a output - can't seem to find info anywhere on the net.
Specifically - looking to understand the following:
Flags=8863
Smart
Running (is this the same as UP)
Simplex
inet6
supported media: autoselect - does that imply the... (1 Reply)
Hi,
I wish to format the output of a grep command in such a way that sed will be able to handle the newline characters held in the output.
Since sed does not allow newlines to be contained in a replacement pattern, that means adding a backslash '\' character to the end of each line from... (8 Replies)
Hi all,
Very new to shell scripting so appreciate some help!
There is a process count that I need to monitor, I have the AIX command that gives this value and I've cleaned it up with grep/awk so it only spits out the value I'm interested in:
echo "psc -i 10050 -s RELOAD_SERVICE" | tmadmin... (14 Replies)
I'm trying to gather information on the interfaces on a large number of servers.
If I run ifconfig I will get: eth0 Link encap:Ethernet HWaddr 00:50:56:A2:27:C1
inet addr:10.145.xxx.xxx Bcast:10.152.45.255 Mask:255.255.254.0
-----
eth1 Link... (2 Replies)
Hi,
I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your... (1 Reply)
Dear all,
I have below "ldapsearch" output
$ ldapsearch -D "CN=SVC-ACCOUNT,OU=SVC,OU=VDSI,OU=Non-Human,DC=Org,DC=com" -w secretword -H ldaps://org.com:636 -b DC=Org,DC=com -s sub uid=v00000 "(filter)" "displayName" "uid" "street"
# extended LDIF
#
# LDAPv3
# base <DC=Org,DC=com> with... (7 Replies)
Discussion started by: baluchen
7 Replies
LEARN ABOUT CENTOS
nsd-checkconf
nsd-checkconf(8) nsd 3.2.12 nsd-checkconf(8)NAME
nsd-checkconf - NSD configuration file checker.
SYNOPSIS
nsd-checkconf [-v] [-h] [-o option] [-z zonename] [-s keyname] configfile
DESCRIPTION
nsd-checkconf reads a configuration file. It prints parse errors to standard error, and performs additional checks on the contents. The
configfile format is described in nsd.conf(5).
The utility of this program is to check a config file for errors before using it in nsd(8) or zonec(8). This program can also be used for
shell scripts to access the nsd config file, using the -o and -z options.
OPTIONS -v After reading print the options to standard output in configfile format. Without this option, only success or parse errors are
reported.
-h Print usage help information and exit.
-o option
Return only this option from the config file. This option can to be used in conjunction with the -z option. The special value zones
prints out a list of configured zones.
This option is primarily used by nsdc to parse the config file from the shell. If the -z option is given, but the -o option is not
given, nothing is printed.
-s keyname
Prints the key secret (base64 blob) configured for this key in the config file. Used to help shell scripts parse the config file.
-z zonename
Return the option specified with -o for zone 'zonename'.
If this option is not given, the server section of the config file is used. This option is primarily used by nsdc to parse the con-
fig file from the shell.
The -o, -s and -z option print configfile options to standard output.
FILES
/etc/nsd3/nsd.conf
default NSD configuration file
SEE ALSO nsd(8), nsdc(8), nsd.conf(5), nsd-notify(8), nsd-patch(8), nsd-xfer(8), zonec(8)AUTHORS
NSD was written by NLnet Labs and RIPE NCC joint team. Please see CREDITS file in the distribution for further details.
NLnet Labs jul 19, 2012 nsd-checkconf(8)