I asked a similar question earlier and got a very good answer but a new doubt came up. This is a few lines of a '/sbin/ifconfig' command on my PC:
RX packets:3781025 errors:0 dropped:0 overruns:0 frame:0
TX packets:1941909 errors:0 dropped:0 overruns:0 carrier:0
Does the RX and TX packets... (1 Reply)
I'm trying to install the recommended patch cluster on a x86 Solaris 10 box.
I get this error:
ERROR: /sbin/zonename cannot be found. install_cluster for 10_x86 patch cluster not applied. Exiting.
I tried touching the file and it gave a different error of: expected argument..
anyone... (1 Reply)
I am executing a stored proc and sending the results in a log file. I then want to grab one result from the output parameters (bolded below, 2) so that I can store it in a variable which will then be called in another script. There are more details that get printed in the beginning of the log file,... (3 Replies)
Hi -
Trying to understand a few things from an ifconfig -a output - can't seem to find info anywhere on the net.
Specifically - looking to understand the following:
Flags=8863
Smart
Running (is this the same as UP)
Simplex
inet6
supported media: autoselect - does that imply the... (1 Reply)
Hi,
I wish to format the output of a grep command in such a way that sed will be able to handle the newline characters held in the output.
Since sed does not allow newlines to be contained in a replacement pattern, that means adding a backslash '\' character to the end of each line from... (8 Replies)
Hi all,
Very new to shell scripting so appreciate some help!
There is a process count that I need to monitor, I have the AIX command that gives this value and I've cleaned it up with grep/awk so it only spits out the value I'm interested in:
echo "psc -i 10050 -s RELOAD_SERVICE" | tmadmin... (14 Replies)
I'm trying to gather information on the interfaces on a large number of servers.
If I run ifconfig I will get: eth0 Link encap:Ethernet HWaddr 00:50:56:A2:27:C1
inet addr:10.145.xxx.xxx Bcast:10.152.45.255 Mask:255.255.254.0
-----
eth1 Link... (2 Replies)
Hi,
I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your... (1 Reply)
Dear all,
I have below "ldapsearch" output
$ ldapsearch -D "CN=SVC-ACCOUNT,OU=SVC,OU=VDSI,OU=Non-Human,DC=Org,DC=com" -w secretword -H ldaps://org.com:636 -b DC=Org,DC=com -s sub uid=v00000 "(filter)" "displayName" "uid" "street"
# extended LDIF
#
# LDAPv3
# base <DC=Org,DC=com> with... (7 Replies)
Discussion started by: baluchen
7 Replies
LEARN ABOUT FREEBSD
if_nxge
NXGE(4) BSD Kernel Interfaces Manual NXGE(4)NAME
nxge -- Neterion Xframe 10GbE Server/Storage adapter driver
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device nxge
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_nxge_load="YES"
DESCRIPTION
The nxge driver provides support for Neterion Xframe-I and Xframe-II adapters. The driver supports TCP Segmentation Offload (TSO/LSO), Large
Receive Offload (LRO), Jumbo Frames (5 buffer mode), Header Separation (Rx 2 buffer mode), VLAN, and Promiscuous mode.
For general information and support, please visit the Neterion support page http://www.neterion.com/support/support.html.
Support for Jumbo Frames is provided via the interface MTU setting. Selecting an MTU larger than 1500 bytes with the ifconfig(8) utility
configures the adapter to transmit and receive Jumbo Frames. Xframe adapters support Jumbo Frames up to 9600 bytes.
For Jumbo Frames, the driver will try to allocate physically contiguous buffers. Failures to do so may degrade the performance. To resolve
such problems, please visit http://www.neterion.com where additional information and a kernel patch can be found.
For more information on configuring this device, see ifconfig(8).
HARDWARE
The nxge driver supports Neterion Xframe 10 Gigabit Ethernet adapters listed in http://www.neterion.com/how/pricing.html.
SUPPORT
For troubleshooting tips and FAQs, please visit http://trac.neterion.com/cgi-bin/trac.cgi/wiki/TitleIndex?anonymous.
For any issues please send an email to <support@neterion.com>.
SEE ALSO arp(4), netintro(4), ifconfig(8)HISTORY
The nxge device driver first appeared in FreeBSD 7.0.
AUTHORS
The nxge driver was written by Neterion <support@neterion.com>.
BSD October 16, 2007 BSD